Huawei E5186s-61a Router Manual PDF (Setup & Configuration Guide)
Given below is full router user manual of Huawei E5186s-61a router model. You can also download this manual in PDF Format to read later on your computer.
Product user manuals come handy in case you want to know all functionalities of your device, troubleshooting, fist time configuration & setup and in many other situations.
Page 1 / 3
Quick Start
Page 2 / 3
Thank you for purchasing the CPE. This CPE brings you a
high speed wireless network connection.
This document will help you understand your CPE so you can start using it right away.
Please read this document carefully before using your CPE.
For detailed information about the functions and configurations of the CPE, refer to the
online help on the web management page that comes with the CPE.
Getting to Know Your CPE
Note:
During thunderstorms and rainy weather, turn off and disconnect the CPE.
The CPE function descriptions and illustrations in this document are for your
reference only. The product you have purchased may vary.
Application Scenario
The CPE can:
Provide Internet access for Wi-Fi devices and computers.
Connect to telephones for voice services.
Note:
When connected to a 2G network, the CPE supports circuit switched (CS) calls but not
VoIP.
Connect to fax machines for fax services.
Be used to save and share files in USB storage devices.
Connect to a USB printer.
Expand LAN coverage together with hubs and switches.
Scenario 1: Accessing the Internet Using an LTE, 3G, or 2G Network
The CPE uses your operator's LTE, 3G, or 2G network to access the Internet.
LTE/3G/2G
Note:
When the CPE is in use, you can alter its position or orientation to improve signal
reception.
The external antenna is an optional accessory. If it is not included in the package,
you may contact an authorized dealer to buy an external antenna compatible with
the CPE.
Scenario 2: Accessing the Internet Using Ethernet (WAN)
Connect the CPE's LAN4/WAN port to an Ethernet port using a network cable. You can
then access the Internet through Ethernet, such as a home ADSL, hotel DHCP, or campus
static IP broadband network. To access the Internet through Ethernet:
1.
Use the network cable to connect the CPE to the Ethernet port.
2.
Log in to the CPE's web management page and configure the parameters of the
Ethernet connection.
Dynamic IP: Does not need to be configured.
PPPoE: Enter the user name and password for a dial-up connection.
Static IP: Select static IP in connection mode and enter the IP address, default gateway address,
DNS server address, and so on.
Note:
For detailed information about the user name, password, IP address, default gateway
address, DNS server address, and other settings, contact your operator.
3.
When
is steady green, the Ethernet connection is successful
.
WAN/Ethernet
Selecting the Installation Environment
Obstacles such as concrete and wooden walls will affect the transmission of the network
signal. It is recommended that when you install CPE you choose an open space.
Keep the CPE away from equipment that generates strong magnetic and electric fields, for
instance microwaves, refrigerators, and satellite receivers.
Appearance
101112 13
15
14
17
16
18
1 2
3
4
5
7
8
6
9
○
1
Power indicator
On: CPE turned on
Off: CPE turned off
○
2
Mode indicator
Steady cyan: The CPE is connected to an LTE network.
Steady blue: The CPE is connected to a 3G network.
Steady yellow: The CPE is connected to a 2G network.
Steady green: The CPE is connected to an Ethernet network.
Steady red:
−
The micro SIM card is not recognized, the PIN has not been entered, or the PIN
verification failed.
−
The CPE failed to connect to a wireless network.
−
The CPE is overheating. Its network connection is disconnected so the device can
cool down.
○
3
Wi-Fi indicator
On: Wi-Fi function enabled
Page 3 / 3
Blinking: WPS interconnection verification is in progress. This process should not take
longer than 2 minutes.
Off: Wi-Fi function disabled
○
4
Voice indicator
On: Off-hook condition
Blinking: Incoming call
Off: On-hook condition
○
5
Signal indicator
On: Indicates network signal strength. Full light indicates strong signal.
Off: No network signal.
○
6
Micro SIM card slot
Accommodate a micro SIM card.
○
7
Wi-Fi button
Press and hold for less than 1 second to enable or disable the Wi-Fi function.
Note:
The CPE supports 2.4 GHz and 5 GHz Wi-Fi networks.
○
8
Reset button
Press and hold for more than 3 seconds to restore the CPE to its factory settings.
Note:
Restoring the default settings of the CPE will override all the previous settings.
○
9
WPS button
When WPS is enabled, press and hold the button for one to five seconds to set up a 2.4
GHz WPS connection, or press and hold the button for more than five seconds to set up a
5 GHz WPS connection.
○
10
Power button
Press this button to power the CPE on or off.
○
11
Power port
Connect to the CPE's power adapter.
○
12
USB port
Connect to a USB storage device or USB printer.
Note:
The CPE supports USB 1.1 and 2.0 storage devices in FAT16, FAT32, ext2, and ext3
formats. Storage devices with power supply requirements exceeding USB standards
may not work properly. It is recommended that you prepare an external power
supply in these cases.
The CPE is compatible with samba-supported USB printers.
This port cannot be connected to USB host devices, such as computers.
○
13
TEL ports (RJ11)
Connect to telephones or a fax machine.
Note:
Do not connect a telephone and fax machine to the CPE simultaneously.
○
14
LAN ports (RJ45)
Connect to computers, switches, or other network devices.
○
15
LAN4/WAN port (RJ45)
Connect to an Ethernet port, computer, switch, or other network device.
○
16
LAN4/WAN indicator
On: The port is connected to an Ethernet port or device.
Blinking: Data is being transmitted through the port.
Off: The port is not connected to an Ethernet port or device.
○
17
LAN indicators
On: The port is connected to a device.
Blinking: Data is being transmitted through the port.
Off: No device is connected to the port.
○
18
External antenna ports (SMA-J)
Connect to external antennas (optional).
Note:
Before you connect an external antenna to the CPE, remove the CPE's rear cover.
Getting Started
Installing the Micro SIM Card
Install the micro SIM card according to the illustration.
Note:
When removing the micro SIM card, gently press the micro SIM card in, then
release. The card will automatically pop out.
Do not remove the micro SIM card when the CPE is powered on. Doing so will
affect the performance of your CPE, and data stored on the micro SIM card may be
lost.
Connecting to a Power Adapter
Install the power adapter according to the illustration.
Note:
Use the provided power adapter. Use of an incompatible power adapter or one
from an unknown manufacturer may cause the CPE to malfunction, fail, or could
even cause a fire. Such use voids all warranties, whether expressed or implied, on
the product.
The CPE's power adapter model is HW-120200XYW. X and Y represent letters or
numbers that vary by region. For details about the specific adapter model, contact
an authorized dealer.
Logging In to the Web Management Page
The web-based configuration utility can be used for initial CPE installation, parameter
configuration, and function management through the browser.
The Windows 7 operating system and Internet Explorer 8.0 are used as an example. Ensure
that the CPE is connected to the computer. Follow these steps to log in to the web
management page:
1.
Connect CPE cables.
2.
Configure the computer's IP address so that the IP addresses of the computer and the
CPE are in the same network segment.
Note:
The CPE's default IP address is 192.168.8.1, the subnet mask is 255.255.255.0.
It is recommended that you use the automatically obtained IP addresses for the
computer and domain name system (DNS) server. If you manually configure the
computer IP address, you must set the DNS server IP address to the CPE's IP
address. Otherwise, you will fail to log in to the web management page.
19216811.live