Huawei BM635 Router Manual PDF (Setup & Configuration Guide)

Page 16 / 56 Scroll up to view Page 11 - 15

1 Description

EchoLife BM635

User Guide

1-4

Huawei Proprietary and Confidential

Issue 01 (2008-06-15)

Button

Description

RESET

Press and hold the button for one second to eight seconds to

reboot the BM635.

Press and hold this button for over eight seconds to restore the

carrier settings of the BM635.

Once you restore the carrier settings, all the customized data

will be lost. Use this function with caution.

Note:

WPS: Wi-Fi protected setup

The schematic diagram of the side panel is turned anticlockwise at 90 degrees.

1.3 Installing the

BM635

1.3.1 Selecting the Installation Environment

z

The obstacles, such as a cement wall and a wooden wall affect signal transmission of

the WiMAX network. An open place is recommended for installing the BM635.

z

Place the BM635 far away from an electrical device that produces a strong magnetic

field or strong electric field, such as a microwave oven, a fridge and a satellite dish

antenna.

1.3.2 Rotating the Base

Rotate the supports on the base of the BM635 anticlockwise at 90 degrees so that the

supports are vertical to the BM635, as shown in Figure 1-4.

Figure 1-4

Schematic diagram of rotating the base

Page 17 / 56

EchoLife BM635

User Guide

1 Description

Issue 01 (2008-06-15)

Huawei Proprietary and Confidential

1-5

1.3.3 Connecting Cables

Figure 1-5

Cable connection diagram of the BM635

1

2

3

4

5

6

LAN4

POWER

LAN1

LAN2

LAN1

LAN2

LAN3

LAN4

TEL1

TEL2

1

Power adapter

2

Computer

3

Set top box

4

Switch

5

Fax

6

Phone

Use the cables and power adapters delivered with the BM635.

The schematic diagram of the cable connection is for reference only. You only need to

connect a required device to the BM635.

When the cables are connected correctly, the BM635 will search the WiMAX network

automatically, and can be used after the network is connected successfully.

Page 18 / 56

EchoLife BM635

User Guide

2 Configuring the Network

Issue 01 (2008-06-15)

Huawei Proprietary and Confidential

2-1

2

Configuring the Network

About

This

Chapter

The following table lists the contents of this chapter.

Section

Describes

2.1 Logging in to the Web

UI

How to set the parameters for logging in to the Web

UI.

2.2 Configuring a WAN

How to set the parameters on the WAN side.

2.3 Configuring a LAN

How to set the parameters on the LAN side.

Page 19 / 56

2 Configuring the Network

EchoLife BM635

User Guide

2-2

Huawei Proprietary and Confidential

Issue 01 (2008-06-15)

2.1 Logging in to the Web UI

Before configuring the network, log in to the Web UI. Take the Windows XP operating

system and the Internet Explorer 6.0 as examples.

Perform the following steps to log in to the Web UI.

Step 1

Configure the IP address of the computer so that the IP address of the computer and the

IP address of the BM635 are in the same network segment.

Note:

By default, the IP address of the BM635 is 192.168.1.1 and the subnet mask is 255.255.255.0.

For example, you can set the IP address of the computer to 192.168.1.100 and the subnet mask

to 255.255.255.0.

Step 2

Open the Internet Explorer, enter

http://192.168.1.1

in the address bar, and then press

Enter

.

Step 3

Enter the user name and the password in the login interface that is displayed, and then

click

Login

.

Note:

The initial user name is

admin

and the corresponding password is also

admin

.

Step 4

After the authentication of the user name and the password succeeds, log in to the Web

UI.

----End

2.2 Configuring a WAN

When you configure a WAN, the BM635 can act as a routing device or bridge device.

With the BM635, a terminal at the LAN side is connected to the network.

z

In routing mode, the BM635 acts as a routing device to connect to the network.

Based on packet information, the BM635 searches for a route over which the packets

are sent to the destination IP address.

z

In bridge mode, the BM635 acts as a bridge device to connect to the network. The

BM635 only transparent transmit packets.

Three modes of obtaining an IP address are available for the BM635:

z

Dynamic Host Configuration Protocol (DHCP) mode: The IP address is obtained

from the Internet service provider (ISP).

z

Static IP address mode: The ISP configures a static IP address.

z

Point-to-Point Protocol over Ethernet (PPPoE) mode: The IP address is obtained by

PPPoE dialup.

Page 20 / 56

EchoLife BM635

User Guide

2 Configuring the Network

Issue 01 (2008-06-15)

Huawei Proprietary and Confidential

2-3

2.2.1 Configuring the Routing Mode

Configuring the DHCP Routing Mode

Step 1

In the navigation tree, choose

Basic

>

WAN

, and then click the

WAN

tab.

Step 2

Select

Route

from

Mode

.

Step 3

Select

DHCP Auto get IP address from ISP

.

Step 4

Select whether to enable the network address transmission (NAT) function, if enable, the

NAPT type is recommended.

Note:

When the NAT function is enabled to facilitate translation of IP addresses, the host IP address

of LAN can be effectively hidden. Thus, the security of the intranet is ensured. Two NAT

modes are available:

z

network address port translation (NAPT)

z

CONE NAT

Step 5

Click

Apply

.

----End

Configuring the Static IP Routing Mode

Step 1

In the navigation tree, choose

Basic

>

WAN

, and then click the

WAN

tab.

Step 2

Select

Route

from

Mode

.

Step 3

Select

Static Get static IP address from ISP

.

Step 4

Select whether to enable the network address transmission (NAT) function, if enable, the

NAPT type is recommended.

Note:

When the NAT function is enabled to facilitate translation of IP addresses, the host IP address

of LAN can be effectively hidden. Thus, the security of the intranet is ensured. Two NAT

modes are available:

z

network address port translation (NAPT)

z

CONE NAT

Step 5

Enter the IP address in the

IP Address

text box.

Step 6

Enter the BM635 subnet mask in the

Subnet Mask

text box.

Step 7

Enter the BM635 default gateway in the

Default Gateway

text box.

Step 8

Enter the IP address of primary domain name server (DNS) in the

Primary DNS Server

text box.

Step 9

Enter the IP address of secondary DNS in the

Secondary DNS Server

text box.

Note:

IP Address, Subnet Mask, Default Gateway, Primary DNS Server, Secondary DNS Server is

supplied by the carrier.

Step 10

Click

Apply

.

Rate

Popular Huawei Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share