1. Home
    2. /
  2. Manuals
    3. /
  3. Hitron
    4. /
  4. CGNM-3552-ROG
    5. /
  5. 19
Page 91 / 135 Scroll up to view Page 86 - 90
WIRELESS
Version 2.0, 07/2015. Copyright
2015 Hitron Technologies
13
Hitron CGNM/ CGNM-3552 User’s Guide
5.2.3
WPS
Use this screen to manage WiFi Protected Setup (WPS).
NOTE:
It is strongly recommended that you set up security on your network;
otherwise, anyone in the radio coverage area can access your network.
Click
Wireless
>
Basic Settings
, then click the
WPS
tab. The following screen
displays.
Encryption Mode
Select the type of encryption you want to use. The
options that display depend on the
Security Mode
you
selected.
WEP
:
Select
WEP64
to use a ten-digit security key.
Select
WEP128
to use a twenty-six-digit security
key.
WPA
,
WPA2
and
WPA/WPA2
:
Select
TKIP
to use the Temporal Key Integrity
Protocol.
Select
AES
to use the Advanced Encryption
Standard.
Select
TKIP/AES
to allow clients using either encryption
type to connect to the CGNM/ CGNM-3552.
Pass Phrase
Enter the security key or password that you want to use
for your wireless network. You will need to enter this key
into your wireless clients in order to allow them to
connect to the network.
Save Changes
Click this to save your changes to the fields in this
screen.
Cancel
Click this to return the fields in this screen to their last-
saved values without saving your changes.
Help
Click this to see information about the fields in this
screen.
Table 27:
The Wireless: Basic Settings Screen (5G) (continued)
Page 92 / 135
WIRELESS
Version 2.0, 07/2015. Copyright
2015 Hitron Technologies
14
Hitron CGNM/ CGNM-3552 User’s Guide
Figure 37:
The Wireless: Basic Settings Screen (WPS)
The following table describes the labels in this screen.
Table 28:
The Wireless: Basic Settings Screen (WPS)
WPS Settings
WPS Method
Use these buttons to run WiFi Protected Setup (WPS):
Click the
PBC
button and then
Push Button
to begin
the Push-Button Configuration process. You must
then press the PBC button on your client wireless
devices within two minutes in order to register them
on your wireless network.
Click the
PIN
button to begin the PIN configuration
process. In the screen that displays, enter the WPS
PIN that you want to use for the CGNM/ CGNM-
3552, or the WPS PIN of the client device you want
to add to the network.
WPS Status
This displays whether or not the CGNM/ CGNM-3552 is
using WiFi Protected Setup.
WPS Configure
Status
This displays the WiFi Protected Setup configuration for
the wireless network.
WPS Configure
Status (5G)
This displays the WiFi Protected Setup configuration for
the 5G wireless network.
Help
Click this to see information about the fields in this
screen.
Page 93 / 135
WIRELESS
Version 2.0, 07/2015. Copyright
2015 Hitron Technologies
15
Hitron CGNM/ CGNM-3552 User’s Guide
5.3
The Access Control Screen
Use this screen to configure Media Access Control (MAC) address filtering on the
wireless network.
NOTE:
To configure MAC address filtering on the wired LAN, see
The Device Filter
Screen
on page
100
.
You can set the CGNM/ CGNM-3552 to allow only certain devices to access the
CGNM/ CGNM-3552 and the network wirelessly, or to deny certain devices access.
Click
Wireless
>
Access Control
. The following screen displays.
Figure 38:
The Wireless: Access Control Screen
The following table describes the labels in this screen.
Table 29:
The Wireless: Access Control Screen
Connected Devices
Host Name
This displays the name of each network device that has
connected to the CGNM/ CGNM-3552 on the wireless
network.
IP Address
This displays the IP address of each network device that
has connected to the CGNM/ CGNM-3552 on the
wireless network.
Page 94 / 135
WIRELESS
Version 2.0, 07/2015. Copyright
2015 Hitron Technologies
16
Hitron CGNM/ CGNM-3552 User’s Guide
MAC Address
This displays the MAC address of each network device
that has connected to the CGNM/ CGNM-3552 on the
wireless network.
Type
This displays whether the device’s IP address was
assigned by DHCP (
DHCP-IP
), or
self-assigned
.
Interface
This displays the name of the interface on which the
relevant device is connected.
Status
This displays if the device filter is active or not.
Action
Click
Manage
to make changes to the device’s filtering
status; see
Adding or Editing a Managed Device
on
page
17
for information on the screen that displays.
Managed Devices
Block Rules
Use these buttons to control the action to be taken for
the devices listed:
Select
Allow All
to ignore the
Devices
list and let
all devices connect wirelessly to the CGNM/
CGNM-3552.
Select
Allow
to permit only devices you added to
the
Devices
list to access the CGNM/ CGNM-3552
and the network wirelessly. All other devices are
denied access.
Select
Deny
to permit all devices except those you
added to the
Devices
list to access the CGNM/
CGNM-3552 and the network wirelessly. The
specified devices are denied access.
Host Name
This field displays the name of the wireless device.
MAC Address
This field displays the device’s MAC (Media Access
Control) address.
Action
Click
Manage
to make changes to the device’s filtering
status; see
Adding or Editing a Managed Device
on
page
17
for information on the screen that displays.
Save Changes
Click this to save your changes to the fields in this
screen.
Add Managed Device
Click this to add a new service filtering rule (see
Adding or
Editing a Managed Device
on page
17
).
Help
Click this to see information about the fields in this
screen.
Table 29:
The Wireless: Access Control Screen (continued)
Page 95 / 135
WIRELESS
Version 2.0, 07/2015. Copyright
2015 Hitron Technologies
17
Hitron CGNM/ CGNM-3552 User’s Guide
5.3.1
Adding or Editing a Managed Device
To add a new managed device, click
Add Managed Device
in the
Wireless
>
Access Control
screen.
To edit an existing managed device, locate the device in the
Wireless
>
Access
Control
screen and click its
Manage
button.
The following screen displays.
Figure 39:
The Wireless: Access Control
Add/Edit
Screen
The following table describes the labels in this screen.
Table 30:
The Wireless: Access Control
Add/Edit
Screen
Host Name
Enter the name of the wireless device.
MAC Address
Enter the device’s MAC (Media Access Control)
address.
Device Managed
Use this field to define whether the device should have
its access privileges filtered or not.
Click
Yes
to filter the device’s access privileges.
Click
No
not to filter the device’s access privileges.
Apply
Click this to save your changes to the fields in this
screen.
Close
Click this to return to the
Wireless Access Control
screen without saving your changes to the rule.

Rate

4.3 / 5 based on 3 votes.

Popular Hitron Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top