Hawking HWRN2 Router Manual PDF (Setup & Configuration Guide)

Page 106 / 136 Scroll up to view Page 101 - 105

97

3-3-1 Access Control

This function allows or denies computers with specific MAC address

from connecting to the network; it can also allow or deny computers with

specific IP address, protocol, or port.

Please click ‘Security’ tab at the top of web management interface, then

click ‘Access Control’, and the following message will be displayed on

your web browser:

1

2

3

5

6

7

8

9

10

13

14

15

16

11

4

12

Page 107 / 136

98

Here are descriptions of every setup items:

Enable MAC Filtering

Check this box to enable MAC address based filtering,

(1):

and please select ‘Deny’ or ‘Allow’ to decide the behavior of

MAC filtering table. If you select deny, all MAC addresses

listed in filtering table will be denied from connecting to the

network; if you select allow, only MAC addresses listed in

filtering table will be able to connect to the network, and

rejecting all other network devices.

Client PC

Please input the MAC address of computer or network

MAC Address (2):

device here, dash ( - ) or colon ( : ) are not required. (i.e. If

the MAC address label of your wireless device indicates

‘aa-bb-cc-dd-ee-ff’ or ‘aa:bb:cc:dd:ee:ff’, just input

‘aabbccddeeff’

Computer Name (3):

Pull down the menu and all the computers connected to the

router will be listed here. You can easily to select the

computer name without checking the IP address of the

computer.

Comment (4):

You can input any text here as the comment of this MAC

address, like ‘ROOM 2A Computer’ or anything. You can

input up to 16 alphanumerical characters here. This is

optional and you can leave it blank, however, it’s

recommended to use this field to write a comment for every

MAC addresses as a memory aid.

Add (5):

Click ‘Add’ button to add the MAC address and associated

comment to the MAC address filtering table.

Reset (6):

Remove all inputted values.

MAC Filtering

All existing MAC addresses in filtering table

Table (7):

will be listed here.

Delete Selected (8):

If you want to delete a specific MAC address entry, check the

Page 108 / 136

99

‘select’ box of the MAC address you want to delete, then

click ‘Delete Selected’ button. (You can select more than one

MAC addresses).

Delete All (9):

If you want to delete all MAC addresses listed here, please

click ‘Delete All’ button.

Reset (10):

You can also click ‘Reset’ button to unselect all MAC addresses.

Enable IP

Check this box to enable IP address based filtering, and

Filtering Table (11):

please select ‘Deny’ or ‘Allow’ to decide the behavior of IP

filtering table. If you select deny, all IP addresses listed in

filtering table will be denied from connecting to the network;

if you select allow, only IP addresses listed in filtering table

will be able to connect to the network, and rejecting all other

network devices.

IP Filtering

All existing IP addresses in filtering table will be listed here.

Table (12):

Add PC (13):

Click this button to add a new IP address to IP filtering table,

up to 20 IP addresses can be added.

Please refer to

section 3-3-1-1 ‘Add PC’ below.

Delete

If you want to delete a specific IP address entry,

Selected (14):

check the ‘select’ box of the IP address you want to delete,

then click ‘Delete Selected’ button. (You can select more than

one IP addresses).

Delete All (15):

If you want to delete all IP addresses listed here, please click

‘Delete All’ button.

Page 109 / 136

100

After you finish with all settings, please click ‘Apply’ (16) button and the

following message will be displayed on your web browser:

Please click ‘Continue’ to go back to previous setup menu; to continue on

other setup procedures, or click ‘Apply’ to reboot the router so the

settings will take effect (Please wait for about 30 seconds while router is

rebooting).

If you want to reset all settings in this page back to previously-saved

value, please click ‘Cancel’ button.

3-3-1-1 Add PC

After button is clicked, the following message will be displayed on your

web browser:

a

b

c

Page 110 / 136

101

Here are descriptions of every setup items:

Client PC

Please input any text to describe this IP

Description (a):

address, up to 16 alphanumerical characters.

Client PC IP

Please input the starting IP address in the left

address (b):

field, and input the end IP address in the right field to define

a range of IP addresses, or just input the IP address in the

left field to define a single IP address.

Client PC

Please check all services you want to allow or

Service (c):

deny this IP address to use, you can check multiple services.

Rate

Popular Hawking Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share