48

Please follow the following instructions to set wired LAN parameters:

Please click ‘Home Network’ tab at the left menu of the web management

interface, there are three setup groups here: ‘LAN IP’, ‘DHCP Server’, and

‘Static DHCP Leases Table’. Here are setup instructions for each of them:

49

2-6-1 LAN IP section:

Here are descriptions of every setup item:

IP address (1):

Please input the IP address of this Smart Repeater.

This is the IP address used to access your Smart

Repeater.

Make sure to make note of the new IP

Address after you change it since the old one will no

longer work.

Subnet Mask (2):

Please input subnet mask for this network.

802.1d

If you wish to activate 802.1d spanning tree

Spanning Tree (3):

function, select ‘Enabled’ for setup item ‘802.1d

Spanning Tree’, or set it to ‘Disabled’

DHCP Server (4):

If you want to activate DHCP server function of this

Smart Repeater, select ‘Enabled’, or set it to ‘Disabled’.

If you select Disable, the IP settings from your source

Internet network will be passed through to clients

connecting through the Smart Repeater.

(For example,

a network with a DHCP server IP range of 10.1.1.1 –

10.1.1.100 will disperse IP addresses within that range

to computers connecting through your Smart Repeater

while the Smart Repeater is connected to that specific

network)

1

3

2

4

Recommended Value if you don’t know what to fill:

IP Address: 192.168.1.200

Subnet Mask: 255.255.255.0

802.1d Spanning Tree: Disabled

DHCP Server: Enabled

50

2-6-2 DHCP Server:

These settings are only available when ‘DHCP Server’ in ‘LAN IP’ section is

‘Enabled’, and here are descriptions of every setup item:

Lease Time (1):

Please choose a lease time (the duration that every

computer can keep a specific IP address) of every IP

address assigned by this Smart Repeater from

dropdown menu.

Start IP (2):

Please input the start IP address of the IP range.

End IP (3):

Please input the end IP address of the IP range.

Domain Name (4):

If you wish, you can also optionally input the domain

name for your network. This is optional.

Recommended Value if you don’t know what to fill:

Lease Time: Two Weeks (or ‘Forever’, if you have less than 20 computers)

Start IP: 192.168.1.20000

End IP: 192.168.1.200

Domain Name: (leave it blank)

NOTE:

1. The number of the last field (mentioned ‘d’ field) of ‘End IP’ must be greater than

‘Start IP’, and can not be the same as Smart Repeater’s IP address.

2. The former three fields of IP address of ‘Start IP’, ‘End IP’, and ‘IP Address of ‘LAN

IP’ section (mentioned ‘a’, ‘b’, and ‘c’ field) should be the same.

3. These settings will affect wireless clients too.

1

3

4

2

51

2-6-3 Static DHCP Leases Table:

This function allows you to assign a static IP address to a specific computer

forever, so you don’t have to set the IP address for a computer, and still

enjoy the benefit of using DHCP server. A maximum of 16 static IP

addresses can be assigned here.

(If you set ‘Lease Time’ to ‘forever’ in ‘DHCP Server’ section, you can also

assign an IP address to a specific computer permanently, however, you will

not be able to assign a certain IP address to a specific computer, since IP

addresses will be assigned in random order by this way).

Here are descriptions of every setup item:

Enable Static

Check this box to enable this function,

DHCP Leases (1):

otherwise uncheck it to disable this function.

MAC Address (2):

Input the MAC address of the computer or network

device (total 12 characters, with characters from 0 to

9, and from a to f, like ‘001122aabbcc’)

IP address (3):

Input the IP address you want to assign to this

computer or network device

‘Add’ (4):

After you inputted MAC address and IP address pair,

click this button to add the pair to static DHCP leases

table.

1

2

3

4

52

If you want to remove all characters you just entered, click ‘Clear’.

After you clicked ‘Add’, the MAC address and IP address mapping will be

added to ‘Static DHCP Leases Table’ section.

If you want to delete a specific item, please check the ‘Select’ box of a MAC

address and IP address mapping (1), then click ‘Delete Selected’ button (2);

if you want to delete all mappings, click ‘Delete All’ (3). If you want to

deselect all mappings, click ‘Reset (4).

After you finish all LAN settings, please click ‘Apply’ button on the bottom of

this page. After you click ‘Apply’, the following message will be displayed on

your web browser:

Press ‘Go Back to save the settings made and go back to the web

management interface; press ‘Apply’ to save the settings made and restart the

Smart Repeater so the settings will take effect after it reboots.

1

2

3

4