Ericsson W35 Router Manual PDF (Setup & Configuration Guide)

Page 81 / 98 Scroll up to view Page 76 - 80

PC Configuration

1/1551-CRH 102 168 Uen Rev A

2008-12-16

75

6.3.4.1

Printer Supporting the Samba Protocol

Follow the steps below to set up a connection to a shared printer from a PC

using Windows XP (similar interface in Windows 2000):

1.

Connect the printer to the USB port on the Ericsson W3x.

2.

In the Windows task bar, click the

Start

button, and select

Run…

.

3. Type

\\<host_name>

in the

Open

field and press Enter. The shared

printer is displayed.

4.

Right click on the printer and select

Connect...

5.

If you don’t have the correct printer drivers installed a pop up window

appears. Click

OK

to install the drivers.

6.

Select a manufacturer and a printer in the

Add Printer Wizard

window

or click

Have disk…

.

7.

Your computer now tries to connect to the shared printer. This could

take a few minutes.

8.

Print a test page to verify that your printer is connected properly. In the

Windows task bar, click the

Start

button

, and select

Printers and

Faxes

. Your shared printer will be displayed as

<printer name> on

<host_name>

. Right-click on the printer icon and select

Properties…

.

On the

General

tab, click on

Print Test Page

.

6.3.4.2

Printer Supporting the RAW Protocol

Follow the steps below to set up a connection to a shared printer from a PC

using Windows XP (similar interface in Windows 2000):

1.

Connect the printer to the USB port on the Ericsson W3x.

2.

In the Windows task bar, click the

Start

button and select

Settings

followed by

Printers and Faxes

. A new window appears including

printers connected to the PC.

3. Select

Add a printer

. The

Add Printer Wizard

appears. Click

Next>

to proceed.

4. In the

Local or Network Printer

window, select

Local printer

attached to this computer

and click

Next>

.

5. In the

Select a Printer Port

window, check

Create a new port

and

from the

Type of port

drop-down list select

Standard TCP/IP Port

.

Click

Next>

.

Page 82 / 98

PC Configuration

76

1/1551-CRH 102 168 Uen Rev A

2008-12-16

6. The

Add Standard TCP/IP Printer Port Wizard

opens. Click

Next>

to

proceed.

7. In the

Add Port

window and

Printer Name or IP Address

field enter

the IP address of the Ericsson W3x (preconfigured

192.168.1.1

) and a

Port Name

, for example IP_192.168.1.1.

Click

Next>

.

8. In the

Additional Port Information Required

window, select the

Custom

checkbox and click the

Settings…

button.

9. In the

Configure Standard TCP/IP Port Monitor

window, select

Raw

as

Protocol

and type

9100

as

Port Number

below

Raw Settings

.

10. Click

OK

to return to the wizard and click

Next>

to proceed.

11. In the

Completing the Add Standard TCP/IP Printer Port Wizard

window, verify your settings and click

Finish

.

12. The

Add Printer Wizard – Install Printer Software

window is

displayed. Select the

Manufacturer

and

Printer

and click

Next>

.

13. Enter a name for your printer and click

Next>

.

14. Select

Do not share this printer

option and click

Next>

.

15. Print a test page to verify that your printer setup is working properly and

then click

Next>

to proceed. It could take a minute or two for the test

page to be printed.

16. Click

Finish

in the

Add Printer Wizard

.

17. Repeat these steps if you have further computers which should have

access to the shared printer.

Page 83 / 98

Troubleshooting

1/1551-CRH 102 168 Uen Rev A

2008-12-16

77

7

Troubleshooting

This chapter describes how to solve a number of issues that could occur

during installation, configuration, and use of the Ericsson W3x. More

information is available at

www.ericsson.com/fwt

.

If none of the suggested methods in this chapter solve your problem, you

are recommended to:

1.

Restart the Ericsson W3x (see section 7.1).

2.

Reset the Ericsson W3x to factory default configuration (see section

7.2).

3.

Contact your service provider.

7.1

Restart

To restart the Ericsson W3x, click the

Restart

button on the

System

web

page.

If you cannot access the WUI, remove the power cable to disconnect the

Ericsson W3x from power and wait a moment before reconnecting the

cable.

7.2

Reset to Factory Default Settings

The factory default configuration contains the original settings of your

Ericsson W3x.

To reset the configuration to factory default settings, click the

Reset

button

in the “FACTORY RESET” section on the

System

web page.

If you cannot access the WUI, the following procedure resets all

configurable values back to factory default settings:

1. Press the

Reset

button with the tip of a pen. The

Standby

button starts

blinking.

2. Wait until the

Standby

button stops blinking which indicates that the

reset is finished.

Page 84 / 98

Troubleshooting

78

1/1551-CRH 102 168 Uen Rev A

2008-12-16

Note:

A reset to factory default configuration cannot be undone. If you

reset the Ericsson W3x to default configuration, all your previous

configuration changes are replaced. If you have previously

changed the password, the

Enter password

page will be

displayed. You have to login to the web pages with the default

password (

user

).

7.3

LAN Connections

Table 25 – LAN Connections

Indication/Symptom

What to do

Cannot access the local network

from a PC that is connected to one

of the Ethernet ports on the

Ericsson W3x.

Check the network cable and make

sure that there is a physical

connection between the PC and the

Ericsson W3x and that at least one

of the corresponding LAN

connector indicators is lit. If not,

make sure that the cable is properly

connected or try with another

Ethernet cable.

Check that the PC is configured to

obtain IP address automatically

using DHCP. If not, change the PC

TCP/IP settings. For instructions,

see section 6.1.1 –

Obtaining IP

Settings Automatically

or refer to

the manual of your operating

system.

Cannot access the WUI on the

Ericsson W3x.

Make sure you are using the

correct LAN IP address in the web

browser. If the LAN IP address has

been changed and you do not know

the current IP address, use the

Reset

button to reset the Ericsson

W3x to factory default configuration

(see section 7.2). This will set the

LAN IP address to 192.168.1.1 and

the web page address to

http://mbr

or

http://192.168.1.1

.

Make sure you are using the

correct login password. If the

default password has been

changed and you do not know the

Page 85 / 98

Troubleshooting

1/1551-CRH 102 168 Uen Rev A

2008-12-16

79

Indication/Symptom

What to do

current password, use the

Reset

button to reset the Ericsson W3x to

factory default configuration (see

section 7.2). This will reset the login

password to the default value

(

user

).

7.4

Internet Access

Table 26 – Internet access

Indication/Symptom

What to do

Cannot access the Internet from

any of my local devices.

Check the status of the Alarm

indicator. If it is blinking, see

the information in the “ALARMS”

section on the

Overview

page.

On the

Internet

page, verify that

the

Link status

is

Up

and that an

IP address

is defined.

The Internet connection is

unacceptable slow or regularly

dropping.

Check the signal quality indicator

on the front of the Ericsson W3x.

The more segments displayed in

the bar graph, the stronger the

signal.

Try to move the Ericsson W3x to

another position or attach an

external antenna (indoor window or

outdoor roof mounted). External

antennas are available as

accessories to the Ericsson W3x.

For optimizing the performance of

the Internet connection, it might be

necessary to change some TCP

settings in the client PC as

described in section 7.4.1 –

Change TCP Settings

.

Cannot access a certain Internet

Check the

NAT

page to make sure

Rate

Popular Ericsson Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share