Engenius ESR-9752 Router Manual PDF (Setup & Configuration Guide)

Page 36 / 94 Scroll up to view Page 31 - 35

36

Click

<Apply>

to save configuration and connect to ISP provider.

±

Wireless Settings

- Basic

In basic setting page, you can set wireless Radio, Mode, Band, SSID, and

Channel.

Radio:

You can turn on/off wireless radio. If wireless Radio is off, you cannot

associate with AP through wireless.

Mode:

In this device, we support three operation modes which are

AP router

and

AP route with WDS

. If you choose AP Router Mode, you can

select AP or WDS function in the drop-down menu.

Band:

You can select the wireless standards running on your network

environment.

Page 37 / 94

37

2.4 GHz(B):

If all your clients are 802.11b, select this one.

2.4 GHz(N):

If all your clients are 802.11n, select this one.

2.4 GHz(B+G):

Either 802.11b or 802.11g wireless devices are in

your environment.

2.4 GHz(G):

If all your clients are 802.11g, select this one.

2.4 GHz(B+G+N):

Either 802.11b, 802.11g, or 802.11n wireless devices

are in your environment.

Enable ESSID:

We support 4 multiple SSIDs in this device. Please select how

many SSIDs you would like to use in your network environment.

ESSID1~4:

ESSID is the name of your wireless network. It might be a unique

name to identify this wireless device in the Wireless LAN. It is case

sensitive and up to 32 printable characters. You might change the

default ESSID for added security.

Auto Channel:

Device will search all valid channels, then select a cleanest

channel and change to this channel if you enable this function.

Depend on this function is enabled or not, you will see different

items below

Auto Channel

.

Channel:

If Auto Channel is disabled, you should choose a static channel and

AP will use this channel to communicate with other clients.

Check Channel Time:

If Auto Channel is enabled, you can choose a period

from the drop-down menu. AP will change to a clean

channel periodically.

Page 38 / 94

38

- WDS with AP Router

Wireless

Distribution

System,

a

system

that

enables

the

wireless

interconnection of access point, allows a wireless network to be extended using

multiple APs without a wired backbone to link them. Each WDS AP needs same

channel and encryption type settings.

MAC address 1~4:

Please enter the MAC address(es) of the neighboring APs

which participate in WDS. There can be maximum of 4

devices now.

Set Security:

WDS Security depends on your AP security settings. Note: it

does not support

mixed mode

such as WPA-PSK/WPA2-PSK

Mixed mode.

Page 39 / 94

39

- Advanced

This tab allows you to set the advanced wireless options.. You should not

change these parameters unless you know what effect the changes will have on

the router.

Fragment Threshold:

This specifies the maximum size of a packet during the

fragmentation of data to be transmitted. If you set this

value too low, it will result in bad performance.

RTS Threshold:

When the packet size is smaller than the RTS threshold, the

wireless router will not use the RTS/CTS mechanism to send

this packet.

Beacon Interval:

This is the interval of time that this wireless router broadcasts

a beacon. A Beacon is used to synchronize the wireless

network.

Page 40 / 94

40

DTIM Period:

Enter a value between 1 and 255 for the Delivery Traffic Indication

Message (DTIM). A DTIM is a countdown informing clients of the

next window for listening to broadcast and multicast messages.

Data Rate:

The “Data Rate” is the rate that this access point uses to transmit

data packets. The access point will use the highest possible

selected transmission rate to transmit the data packets.

N Data Rate:

The “Data Rate” is the rate that this access point uses to transmit

data packets for N compliant wireless nodes. Highest to lowest

data rate can be fixed.

Channel Bandwidth:

This is the range of frequencies that will be used.

Preamble Type:

The “Long Preamble” can provide better wireless LAN

compatibility while the “Short Preamble” can provide better

wireless LAN performance.

CTS Protection:

It is recommended to enable the protection mechanism. This

mechanism can decrease the rate of data collision between

802.11b and 802.11g wireless stations. When the protection

mode is enabled, the throughput of the AP will be a little lower

due to a lot of frame-network that is transmitted.

TX Power:

This can be set to a bare minimum or maximum power.

Rate

Popular Engenius Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share