Engenius ESR-9752 Router Manual PDF (Setup & Configuration Guide)

Page 46 / 94 Scroll up to view Page 41 - 45

46

- Wi-Fi Protected Setup (WPS)

WPS is the simplest way to establish a connection between the wireless clients

and the wireless router. You don’t have to select the encryption mode and fill in a

long encryption passphrase every time when you try to setup a wireless

connection. You only need to press a button on both wireless client and wireless

router, and the WPS will do the rest for you.

The wireless router supports two types of WPS: WPS via Push Button and

WPS via PIN code. If you want to use the Push Button, you have to push a

specific button on the wireless client or in the utility of the wireless client to start

the WPS mode, and switch the wireless router to WPS mode. You can simply

push the WPS button of the wireless router, or click the ‘Start to Process’ button

in the web configuration interface. If you want to use the PIN code, you have to

know the PIN code of the wireless client and switch it to WPS mode, then fill-in

the PIN code of the wireless client through the web configuration interface of the

wireless router.

Page 47 / 94

47

WPS:

Check the box to enable WPS function and uncheck it to disable the WPS

function.

WPS Current Status:

If the wireless security (encryption) function of this

wireless router is properly set, you’ll see a ‘Configured’

message here. Otherwise, you’ll see ‘

UnConfigured’

.

Self Pin Code:

This is the WPS PIN code of the wireless router. You may need

this information when connecting to other WPS-enabled

wireless devices.

SSID:

This is the network broadcast name (SSID) of the router.

Authentication Mode:

It shows the active authentication mode for the wireless

connection.

Passphrase Key:

It shows the passphrase key that is randomly generated by

the wireless router during the WPS process. You may need

this information when using a device which doesn’t support

WPS.

Interface:

If device is set to repeater mode, you can choose

“Client”

interface to

connect with other AP by using WPS, otherwise you may choose

“AP”

interface to do WPS with other clients.

WPS via Push Button:

Press the button to start the WPS process. The router

will wait for the WPS request from the wireless devices

within 2 minutes.

WPS via PIN:

You can fill-in the PIN code of the wireless device and press the

button to start the WPS process. The router will wait for the WPS

request from the wireless device within 2 minutes.

Page 48 / 94

48

- Client List

This WLAN Client Table shows the Wireless client associate to this Wireless

Router.

- Policy

The Broadband router can allow you to set up the Wireless Access Policy.

WAN Connection:

Allow Wireless Client on specific SSID to access WAN port.

Communication

between

Wireless

clients:

Allow

Wireless

Client

to

communicate with other Wireless Client on specific SSID.

Communication between Wireless clients and wired clients:

Allow Wireless

Client to communicate with other Wireless Client on specific SSID and Wired Client

on the switch. Or Wireless Client will allow to access WAN port only

Page 49 / 94

49

±

Firewall Settings

The Broadband router provides extensive firewall protection by restricting

connection parameters, thus limiting the risk of hacker attacks, and defending

against a wide array of common Internet attacks. However, for applications that

require unrestricted access to the Internet, you can configure a specific client/server

as a Demilitarized Zone (DMZ).

Note

: To enable the Firewall settings select Enable and click Apply

- Advanced

You can allow the VPN packets to pass through this Broadband router.

Page 50 / 94

50

- Demilitarized Zone (DMZ)

If you have a client PC that cannot run an Internet application (e.g. Games)

properly from behind the NAT firewall, then you can open up the firewall

restrictions to unrestricted two-way Internet access by defining a DMZ Host. The

DMZ function allows you to re-direct all packets going to your WAN port IP

address to a particular IP address in your LAN. The difference between the

virtual server and the DMZ function is that the virtual server re-directs a particular

service/Internet application (e.g. FTP, websites) to a particular LAN client/server,

whereas DMZ re-directs all packets (regardless of services) from your WAN IP

address to a particular LAN client/server.

Enable DMZ:

Enable/disable DMZ

LAN IP Address:

Fill-in the IP address of a particular host in your LAN Network

or select a PC from the list on the right that will receive all the

packets originally from the WAN port/Public IP address.

Click

<Apply>

at the bottom of the screen to save the above configurations.

Rate

Popular Engenius Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share