Page 41 / 97
Scroll up to view Page 36 - 40
PPTP allows the secure connection over the Internet by simply dialing in to a local
point provided by your ISP provider. The image screen allows client PCs to establish
a normal PPTP session and provides hassle-free configuration of the PPTP client on
each client PC.
Click
<Apply>
to save configuration and connect to ISP provider.
±
WIRELESS
- Basic
In basic setting page, you can set wireless Radio, Mode, Band, SSID, and Channel.
41
Page 42 / 97
Radio:
You can turn on/off wireless radio. If wireless Radio is turned off, the
ENHWI-N3 will not take wireless connections.
Mode:
Three operation modes for selections, the
AP router
and
AP router
with WDS
. If you choose
AP Router
Mode, there will be two selections
under it, the
AP
or
WDS
function in the drop-down menu.
Band:
You can select the wireless standards running on your network
environment such as the following:
2.4 GHz(B):
If all your clients are using 802.11b
2.4 GHz(N):
If all your clients are using 802.11n
2.4 GHz(B+G):
If both 802.11b or a 802.11g
2.4 GHz(G):
If all your clients are using
802.11g
2.4 GHz(B+G+N):
If your clients are mixed using 802.11b,
802.11g, or 802.11n
Enable ESSID:
ENHWI-N3 supports up to 4 SSID. Use the down arrow to
select the number of SSID you wanted to have in your wireless
LAN. Once established you can set the security policy settings
for each. See “Policy” section for more details.
42
Page 43 / 97
ESSID1 to ESSID4:
ESSID is the name of your wireless network. It is
recommended to use a unique name to identify your wireless
device in the LAN. This is case sensitive and up to 32 printable
characters.
Auto Channel:
Disable by default. If Enabled will automatically search all
channels and automatically change to the clearest channel
detected. Different items are visible below the
Auto Channel
.
Channel:
Channel 11 by default.
This is visible only when the
Auto Channel
is
disabled. You can enter your preferred channel number here for the
ENHWI-N3 wireless LAN.
Check Channel Time:
This menu is visible only when the
Auto Channel
is
enabled. Selections are from One Hour to One Week.
This is the duration of when will the ENHWI-N3 check
for and use the clearest channel in the area
automatically.
-
WDS with AP Router
Wireless Distribution System. The WDS is a way of interconnecting wireless
routers and allow an extended wireless network coverage using multiple wireless
routers without the use of a wired backbone. Each WDS AP requires the same
channel and encryption type to work.
43
Page 44 / 97
MAC address 1~4:
Please enter the MAC address(es) of the neighboring APs
that participates in the WDS. A maximum of 4 devices are
allowed.
Set Security:
WDS Security depends on your AP security settings. Note: It
does not support
mixed mode
such as WPA-PSK/WPA2-PSK
Mixed mode.
44
Page 45 / 97
- Advanced
On this tab you can set the advanced wireless settings. If you’re in doubt what to
enter or use here, leave these settings as it is. This is for advance users only. Wrong
parameters can make the router un-operational.
Fragment Threshold:
Default value is 2346.Specifies the maximum size of a
packet during the fragmentation of data to be transmitted. If you set this value
too low, it will result in a bad performance.
RTS Threshold:
Default value is 2347. When the packet size is smaller than
the RTS threshold, the wireless router will not use the RTS/CTS mechanism to
send this packet.
Beacon Interval:
Default value is 100. This is the interval of time that this
wireless router broadcasts a beacon. A Beacon is used to synchronize the
wireless network.
45
19216811.live