¶1

eHome EH100 User Manual

Section ´ - Connecting to a Wireless Network

3.

The

Wireless Network Connection

box will appear. Enter the same

WEP key that is on your router and click

Connect

.

It may take 20-30 seconds to connect to the wireless network. If the

connection fails, please verify that the WEP settings are correct. The

WEP key must be exactly the same as on the wireless router.

¶±

eHome EH100 User Manual

Section ´ - Connecting to a Wireless Network

Configure WPA-PSK

It is recommended to enable WEP on your wireless router or access point before configuring your wireless adapter. If

you are joining an existing network, you will need to know the WEP key being used.

2.

Highlight the wireless network (SSID) you would like to

connect to and click

Connect

.

1.

Open the Windows

®

XP Wireless Utility by right-clicking

on the wireless computer icon in your system tray

(lower-right corner of screen). Select

View Available

Wireless Networks

.

¶²

eHome EH100 User Manual

Section ´ - Connecting to a Wireless Network

3.

The

Wireless Network Connection

box will appear. Enter the

WPA-PSK passphrase and click

Connect

.

It may take 20-30 seconds to connect to the wireless network. If the

connection fails, please verify that the WPA-PSK settings are correct.

The WPA-PSK passphrase must be exactly the same as on the

wireless router.

¶³

eHome EH100 User Manual

Section µ - Troubleshooting

Troubleshooting

This chapter provides solutions to problems that can occur during the installation and operation of the EH-100.

Read

the following descriptions if you are having problems.

(The examples below are illustrated in Windows

®

XP.

If you have

a different operating system, the screenshots on your computer will look similar to the following examples.)

1. Why can’t I access the web-based configuration utility?

When entering the IP address of the eHome router (192.168.0.1 for example), you are not connecting to a website on

the Internet or have to be connected to the Internet. The device has the utility built-in to a ROM chip in the device itself.

Your computer must be on the same IP subnet to connect to the web-based utility.

• Make sure you have an updated Java-enabled web browser. We recommend the following:

• Internet Explorer 5.5 or higher

• Netscape 6 or higher

• Mozilla 1.2.1 (5.0) or higher

• Opera 6.0 or higher

• Safari 1.0 or higher (with Java 1.3.1 or higher)

• Camino 0.7 or higher

• Firefox 1.0 or higher

• Verify physical connectivity by checking for solid link lights on the device. If you do not get a solid link light, try using

a different cable or connect to a different port on the device if possible. If the computer is turned off, the link light may

not be on.

• Disable any internet security software running on the computer. Software firewalls such as Zone Alarm, Black Ice,

Sygate, Norton Personal Firewall, and Windows

®

XP firewall may block access to the configuration pages. Check the

help files included with your firewall software for more information on disabling or configuring it.

¶´

eHome EH100 User Manual

Section µ - Troubleshooting

• Configure your Internet settings:

• Go to

Start

>

Settings

>

Control Panel

. Double-click the

Internet Options

Icon. From the

Security

tab,

click the button to restore the settings to their defaults.

• Click the

Connection

tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings

button. Make sure nothing is checked. Click

OK

.

• Go to the

Advanced

tab and click the button to restore these settings to their defaults. Click

OK

three

times.

• Close your web browser (if open) and open it.

• Access the web management. Open your web browser and enter the IP address of your eHome router in the address

bar. This should open the login page for your the web management.

• If you still cannot access the configuration, unplug the power to the router for 10 seconds and plug back in. Wait

about 30 seconds and try accessing the configuration. If you have multiple computers, try connecting using a different

computer.

2. What can I do if I forgot my password?

If you forgot your password, you must reset your router. Unfortunately this process will change all your settings back

to the factory defaults.

To reset the router, locate the reset button (hole) on the rear panel of the unit. With the router powered on, use a

paperclip to hold the button down for 10 seconds. Release the button and the router will go through its reboot process.

Wait about 30 seconds to access the router. The default IP address is 192.168.0.1. When logging in, the username is

admin

and leave the password box empty.