Page 41 / 92
Scroll up to view Page 36 - 40
41
1.
Click
RUN WIZARD
, there will pop up a new page as shown in the
following figure appears.
2.
Click
EXIT
, this page will be closed. Click
NEXT
, the page as shown in the
following figure appears.
Page 42 / 92
42
In this page, enter a new password for the admin account. After finishing all
quick start settings, it will be saved and effect immediately.
3.
Click
NEXT
, the page as shown in the following figure appears.
In this page, you can select a local time zone.
4.
Click
NEXT
, the page as shown in the following figure appears.
You may select
Auto setup by ISP list
,
Dynamic IP Address, Static IP Address,
PPPoE/PPPoA
or
Bridge Mode
.
5.3.1.
Auto setup by ISP list
Select
Auto setup by ISP list
, click
NEXT
, and the page as shown in the
following figure appears.
Page 43 / 92
43
The following table describes the parameters in this page:
Field
Description
Country
Select the country you are in.
ISP
Select your Internet Service Provider (ISP).
VPI
Virtual path identifier (VPI) is the virtual path between two
points in an ATM network. Its valid value is between 0 and
255. Enter the correct VPI provided by your ISP.
VCI
Virtual channel identifier (VCI) is the virtual channel between
two points in an ATM network. Its valid value is between 1
and 65535. Enter the correct VCI provided by your ISP.
Connection
Type
Select a connection type from the dropdown list. You may
select PPPoE/ PPPoA/ Dynamic IP/ Static IP/ Routered IP/
Bridge.
5.3.2.
Bridge Mode
Select
Bridge Mode
, click
NEXT
, and the page shown in the following figure
will appear.
Page 44 / 92
44
The following table describes the parameters in this page:
Field
Description
VPI
Virtual path identifier (VPI) is the virtual path between two
points in an ATM network. Its valid value is between 0 and
255. Enter the correct VPI provided by your ISP. By default,
VPI is set to
8
.
VCI
Virtual channel identifier (VCI) is the virtual channel between
two points in an ATM network. Its valid value is between 1
and 65535. Enter the correct VCI provided by your ISP. By
default, VCI is set to
35
.
Connection
Type
You can select
LLC
or
VC-Mux
. In this example, the
encapsulation mode is set to
1483 Bridged IP LLC
.
5.3.3.
Dynamic IP Address
For configuration method, please refer to that of Auto setup
by ISP list
Select
Auto setup by ISP list
, click
NEXT
, and the page as shown in the
following figure appears.
The following table describes the parameters in this page:
Field
Description
Country
Select the country you are in.
ISP
Select your Internet Service Provider (ISP).
VPI
Virtual path identifier (VPI) is the virtual path between two
points in an ATM network. Its valid value is between 0 and
255. Enter the correct VPI provided by your ISP.
VCI
Virtual channel identifier (VCI) is the virtual channel between
Page 45 / 92
45
Field
Description
two points in an ATM network. Its valid value is between 1
and 65535. Enter the correct VCI provided by your ISP.
Connection
Type
Select a connection type from the dropdown list. You may
select PPPoE/ PPPoA/ Dynamic IP/ Static IP/ Routered IP/
Bridge.
Bridge Mode
.
Static IP Address
Select
Static IP Address
, click
NEXT
, and the page as shown in the following
figure will appear.
The following table describes the parameters in this page:
Field
Description
VPI
Virtual path identifier (VPI) is the virtual path between two
points in an ATM network. Its valid value is between 0 and
255. Enter the correct VPI provided by your ISP. By default,
VPI is set to
8
.
VCI
Virtual channel identifier (VCI) is the virtual channel between
two points in an ATM network. Its valid value is between 1
and 65535. Enter the correct VCI provided by your ISP. By
default, VCI is set to
35
.
IP Address
Enter the IP address provided by your ISP.
Subnet
Enter the subnet mask provided by your ISP.
19216811.live