1. Home
    2. /
  2. Manuals
    3. /
  3. DrayTek
    4. /
  4. Vigor-2930n
    5. /
  5. 45
Page 221 / 298 Scroll up to view Page 216 - 220
igor2930 Series User’s Guide
213
The application for the WDS-Repeater mode is depicted as below:
The major difference between these two modes is that: while in
Repeater
mode, the packets
received from one peer AP can be repeated to another peer AP through WDS links. Yet in
Bridge
mode, packets received from a WDS link will only be forwarded to local wired or
wireless hosts. In other words, only Repeater mode can do WDS-to-WDS packet forwarding.
In the following examples, hosts connected to Bridge 1 or 3 can communicate with hosts
connected to Bridge 2 through WDS links. However, hosts connected to Bridge 1 CANNOT
communicate with hosts connected to Bridge 3 through Bridge 2.
Click
WDS
from
Wireless LAN
menu. The following page will be shown.
Page 222 / 298
Vigor2930 Series User’s Guide
214
Mode
Choose the mode for WDS setting.
Disable
mode will not
invoke any WDS setting.
Bridge
mode is designed to fulfill
the first type of application.
Repeater
mode is for the second
one.
Security
There are three types for security,
Disable
,
WEP
and
Pre-shared key
. The setting you choose here will make the
following WEP or Pre-shared key field valid or not. Choose
one of the types for the router.
WEP
If you checked the box of
Use the same WEP key …
, you do
not need to choose 64-bit or 128-bit as the Encryption Mode.
If you do not check that box, you can set the WEP key now in
this page.
Pre-shared Key
Type –
There are three types for you to choose.
DrayTek
WPA
can be used for all DrayTek wireless routers like
Vigor2700, Vigor2800, Vigor2820, and etc., except for other
brand's wireless routers.
WPA
and
WPA2
are used for WDS
devices (e.g., AP700). For example, if you have a
wireless AP and a Vigor2820n wireless router, you can set the
Page 223 / 298
igor2930 Series User’s Guide
215
encryption mode as WPA or WPA2 to establish your WDS
system between AP and the router.
Key -
Type 8 ~ 63 ASCII characters or 64 hexadecimal digits
leading by “0x”.
Bridge
If you choose Bridge as the connecting mode, please type in
the peer MAC address in these fields.
Four peer MAC
addresses are allowed to be entered in this page at one time.
Yet please disable the unused link to get better performance.
If you want to invoke the peer MAC address, remember to
check
Enable
box in the front of the MAC address after
typing.
Repeater
If you choose Repeater as the connecting mode, please type in
the peer MAC address in these fields. Four peer MAC
addresses are allowed to be entered in this page at one time.
Similarly, if you want to invoke the peer MAC address,
remember to check
Enable
box in the front of the MAC
address after typing.
Access Point Function
Click
Enable
to make this router serving as an access point;
click
Disable
to cancel this function.
Status
It allows user to send “hello” message to peers. Yet, it is valid
only when the peer also supports this function.
Page 224 / 298
Vigor2930 Series User’s Guide
216
3.13.7 AP Discovery
Vigor router can scan all regulatory channels and find working APs in the neighborhood.
Based on the scanning result, users will know which channel is clean for usage. Also, it can
be used to facilitate finding an AP for a WDS link. Notice that during the scanning process
(about 5 seconds), no client is allowed to connect to Vigor.
This page is used to scan the existence of the APs on the wireless LAN. Yet, only the AP
which is in the same channel of this router can be found. Please click
Scan
to discover all the
connected APs.
If you want the found AP applying the WDS settings, please type in the AP’s MAC address
on the bottom of the page and click Bridge or Repeater. Next, click
Add to
. Later, the MAC
address of the AP will be added to Bridge or Repeater field of WDS settings page.
3.13.8 Station List
Station List
provides the knowledge of connecting wireless clients now along with its status
code. There is a code summary below for explanation. For convenient
Access Control
, you
can select a WLAN station and click
Add to Access Control
below.
Page 225 / 298
igor2930 Series User’s Guide
217
Refresh
Click this button to refresh the status of station list.
Add
Click this button to add current selected MAC address
into
Access Contro
l.

Rate

4.5 / 5 based on 2 votes.

Popular DrayTek Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top