DrayTek Vigor-2930n Router Manual PDF (Setup & Configuration Guide)

Page 216 / 298 Scroll up to view Page 211 - 215

Vigor2930 Series User’s Guide

208

WPA2/802.1x Only-

Accepts only WPA2 clients and the

encryption key is obtained dynamically from RADIUS server

with 802.1X protocol.

Mixed (WPA+WPA2/802.1x only) -

Accepts WPA and WPA2

clients simultaneously and the encryption key is obtained

dynamically from RADIUS server with 802.1X protocol.

WPA/PSK-

Accepts only WPA clients and the encryption key

should be entered in PSK.

WPA2/PSK-

Accepts only WPA2 clients and the encryption key

should be entered in PSK.

Mixed (WPA+ WPA2)/PSK -

Accepts WPA and WPA2

clients simultaneously and the encryption key should be entered

in PSK. Default Pre-Shared Key (PSK) is provided and stated

on the label pasted on the bottom of the router. For the wireless

client who wants to access into Internet through such router,

please input the default PSK value for connection.

WPA

The WPA encrypts each frame transmitted from the radio using

the key, which either PSK (Pre-Shared Key) entered manually

in this field below or automatically negotiated via 802.1x

authentication. Either

8~63

ASCII characters, such as

012345678(or 64 Hexadecimal digits leading by 0x, such as

"0x321253abcde...").

Type

- Select from Mixed (WPA+WPA2) or WPA2 only.

Pre-Shared Key (PSK)

- Either

8~63

ASCII characters, such as

012345678..(or 64 Hexadecimal digits leading by 0x, such as

"0x321253abcde...").

WEP

64-Bit

-

For 64 bits WEP key, either

5

ASCII characters, such

as 12345 (or 10 hexadecimal digitals leading by 0x, such as

0x4142434445.)

128-Bit

-

For 128 bits WEP key, either

13

ASCII characters,

such as ABCDEFGHIJKLM (or 26 hexadecimal digits leading

by 0x, such as 0x4142434445464748494A4B4C4D).

All wireless devices must support the same WEP encryption bit

size and have the same key.

Four keys

can be entered here, but

only one key can be selected at a time. The keys can be entered

in ASCII or Hexadecimal. Check the key you wish to use.

3.13.4 Access Control

For additional security of wireless access, the

Access Control

facility allows you to restrict

the network access right by controlling the wireless LAN MAC address of client. Only the

valid MAC address that has been configured can access the wireless LAN interface. By

clicking the

Access Control

, a new web page will appear, as depicted below, so that you

could edit the clients' MAC addresses to control their access rights.

Page 217 / 298

igor2930 Series User’s Guide

209

Policy

Select to enable any one of the following policy.

Activate MAC address filter-

Allow to set MAC

address list for accessing Access Point. PCs with MAC

address not listed above cannot access AP. In addition,

selected station with MAC address listed above can be

isolated from LAN by checking Isolate the station from

LAN.

Blocked MAC address filter-

Allow to set MAC

address list for denying access AP. However, stations

with MAC address not listed above are allowed to access

AP.

Enable Mac Access Filter

Select to enable the MAC Address filter for wireless

LAN identified with SSID 1 to 4 respectively. All the

clients (expressed by MAC addresses) listed in the box

can be grouped under different wireless LAN. For

example, they can be grouped under SSID 1 and SSID 2

at the same time if you check SSID 1 and SSID 2.

MAC Address Filter

Display all MAC addresses that are edited before.

Client’s MAC Address

-

Manually enter the MAC

address of wireless client.

Attribute

s: Isolate the station from LAN -

select to isolate the

wireless connection of the wireless client of the MAC

address from LAN.

Add

Add a new MAC address into the list.

Page 218 / 298

Vigor2930 Series User’s Guide

210

Delete

Delete the selected MAC address in the list.

Edit

Edit the selected MAC address in the list.

Cancel

Give up the access control set up.

OK

Click it to save the access control list.

Clear All

Clean all entries in the MAC address list.

3.13.5 WPS

WPS (Wi-Fi Protected Setup)

provides easy procedure to make network connection

between wireless station and wireless access point (vigor router) with the encryption of

WPA and WPA2.

Note:

Such function is available for the wireless station with WPS supported.

It is the simplest way to build connection between wireless network clients and vigor router.

Users do not need to select any encryption mode and type any long encryption passphrase to

setup a wireless client every time. He/she only needs to press a button on wireless client, and

WPS will connect for client and router automatically.

There are two methods to do network connection through WPS between AP and Stations:

pressing the

Start PBC

button or using

PIN Code

.

z

On the side of Vigor 2930 series which served as an AP, press

Factory Reset

button

once on the front panel of the router or click

Start PBC

on web configuration interface.

On the side of a station with network card installed, press

Start PBC

button of network

card.

z

If you want to use PIN code, you have to know the PIN code specified in wireless

client. Then provide the PIN code of the wireless client you wish to connect to the

Page 219 / 298

igor2930 Series User’s Guide

211

vigor router.

For WPS is supported in WPA-PSK or WPA2-PSK mode, if you do not choose such mode

in

Wireless LAN>>Security

, you will see the following message box.

Please click

OK

and go back

Wireless LAN>>Security

to choose WPA-PSK or

WPA2-PSK mode and access WPS again.

Below shows

Wireless LAN>>WPS

web page.

Enable WPS

Check this box to enable WPS setting.

WPS Status

Display related system information for WPS. If the

wireless security (encryption) function of the router is

properly configured, you can see ‘Configured’ message

here.

SSID

Display the SSID1 of the router. WPS is supported by

SSID1 only.

Page 220 / 298

Vigor2930 Series User’s Guide

212

Authentication Mode

Display current authentication mode of the router. Only

WPA2/PSK and WPA/PSK support WPS.

Configure via Push Button

Click

Start PBC

to invoke Push-Button style WPS setup

procedure. The router will wait for WPS requests from

wireless clients about two minutes. The WLAN LED on

the router will blink fast when WPS is in progress. It will

return to normal condition after two minutes. (You need

to setup WPS within two minutes)

Configure via Client PinCode

Please input the PIN code specified in wireless client you

wish to connect, and click

Start PIN

button. The WLAN

LED on the router will blink fast when WPS is in

progress. It will return to normal condition after two

minutes. (You need to setup WPS within two minutes)

3.13.6 WDS

WDS means Wireless Distribution System. It is a protocol for connecting two access points

(AP) wirelessly. Usually, it can be used for the following application:

y

Provide bridge traffic between two LANs through the air.

y

Extend the coverage range of a WLAN.

To meet the above requirement, two WDS modes are implemented in Vigor router. One is

Bridge

, the other is

Repeater

. Below shows the function of WDS-bridge interface:

Rate

Popular DrayTek Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share