Page 141 / 173
Scroll up to view Page 136 - 140
Vigor2900 Series User’s Guide
135
Click it to reload the page.
Each line across the screen indicates an active session. The following information is displayed:
Private IP:Port
The internal user’s (PC’s) IP address and port number.
#Pseudo Port
The public port number.
Peer IP:Port
The peer user’s (PC’s) IP address and port number.
Ifno
Stands for interface number. The definition is listed below:
0 --- LAN interface.
1 --- B1 interface.
2 --- B2 interface.
3 --- WAN interface.
4.8 Reboot System
The Web Configurator may be used to restart your router. Click
Reboot System
from
System
Management
to open the following page.
If you want to reboot the router using the current configuration, check
Using current
configuration
and click
OK
. To reset the router settings to default values, check
Using
factory default configuration
and click
OK
. The router will take 5 seconds to reboot the
system.
Page 142 / 173
Vigor2900 Series User’s Guide
136
4.9 Firmware Upgrade (TFTP Server)
Before upgrading your router firmware, you need to install the Router Tools. The
Firmware
Upgrade Utility
is included in the tools. The following web page will guide you to upgrade
firmware by using an example. Note that this example is running over Windows OS
(Operating System).
Download the newest firmware from DrayTek's web site or FTP site. The DrayTek web site is
www.draytek.com (or local DrayTek's web site) and FTP site is ftp.draytek.com.
Click
Firmware Upgrade
from
System Management
to launch the Firmware Upgrade
Utility.
Click
OK
. The following screen will appear. Please execute the firmware upgrade utility first.
For the detailed information about firmware update, please go to Chapter 4.
Page 143 / 173
Vigor2900 Series User’s Guide
137
5
A
A
p
p
p
p
l
l
i
i
c
c
a
a
t
t
i
i
o
o
n
n
a
a
n
n
d
d
E
E
x
x
a
a
m
m
p
p
l
l
e
e
s
s
5.1 Create a LAN-to-LAN Connection Between Remote Office
and Headquarter
The most common case is that you may want to connect to network securely, such as the
remote branch office and headquarter. According to the network structure as shown in the
below illustration, you may follow the steps to create a LAN-to-LAN profile. These two
networks (LANs) should NOT have the same network address.
Settings in Router A in headquarter:
1.
Choose
VPN and Remote Access Setup
on the
Advanced Setup
group.
2.
Select
Remote Access Control
Setup
. The following page will appear. Enable the
necessary VPN service and click
OK
.
3.
Then, return to
VPN and Remote Access Setup
page and choose
PPP General Setup
.
Page 144 / 173
Vigor2900 Series User’s Guide
138
4.
For using
PPP
based services, such as PPTP, L2TP, you have to set general settings in
PPP General Setup
.
For using
IPSec
-based service, such as IPSec or L2TP with IPSec Policy, you have to set
general settings in
IPSec General Setup
, such as the pre-shared key that both parties
have known. Return to
VPN and Remote Access Setup
page and choose
VPN
IKE/IPSec General Setup
.
5.
Return to
VPN and Remote Access Setup
page and choose
LAN-to-LAN
Profile
Setup.
Click on one index number to edit a profile.
Page 145 / 173
Vigor2900 Series User’s Guide
139
6.
Set
Common Settings
as shown below. You should
enable
this profile.
7.
Set
Dial-Out Settings
as shown below to dial to connect to Router B aggressively with
the selected Dial-Out method.
If an
IPSec-based
service is selected, you should further specify the remote peer IP
Address, IKE Authentication Method and IPSec Security Method for this Dial-Out
connection.
If a
PPP-based service
is selected, you should further specify the remote peer IP Address,
Username, Password, PPP Authentication and VJ Compression for this Dial-Out
connection.
19216811.live