DrayTek Vigor2860Vn-plus Router Manual PDF (Setup & Configuration Guide)

Page 781 / 794 Scroll up to view Page 776 - 780

Vigor2860 Series User’s Guide

767

wl ht bw value

The value you can type is 0 (for BW_20) and 1 (for

BW_40).

wl ht gi value

The value you can type is 0 (for GI_800) and 1 (for

GI_4001)

wl ht badecline value

The value you can type is 0 (for disabling) and 1 (for

enabling).

wl ht autoba value

The value you can type is 0 (for disabling) and 1 (for

enabling).

wl ht rdg value

The value you can type is 0 (for disabling) and 1 (for

enabling).

wl ht msdu value

The value you can type is 0 (for disabling) and 1 (for

enabling).

wl ht txpower value

The value you can type ranges from 1 – 6 (level).

wl ht antenna value

The value you can type ranges from 0-3.

0: 2T3R

1: 2T2R

2: 1T2R

3: 1T1R

wl ht greenfield value

The value you can type is 0 (for mixed mode) and 1 (for

green field).

Example

> wl ht bw value 1

BW=0

<Note> Please restart wireless after you set new parameters.

> wl restart

Wireless restart

................

Telnet Command: wl restart

This command allows you to restart wireless setting.

Example

> wl restart

Wireless restart

................

Page 782 / 794

Vigor2860 Series User’s Guide

768

Telnet Command: wl btnctl

This command allows you to enable or disable wireless button control.

wl btnctl

[value]

Syntax Description

Parameter

Description

value

0: disable

1: enable

Example

> wl btnctl 1

Enable wireless botton control

Current wireless botton control is on

>

Telnet Command: wl iwpriv & wl wlanconfig

These two commands are reserved for RD debug. Do not use them.

Telnet Command: wl efuse

This command is used to configure parameters related to wireless RF hardware. At present, it

is not allowed for end user to operate.

Page 783 / 794

Vigor2860 Series User’s Guide

769

Telnet Command: wan vlan

This command allows you to tag packets on WAN VLAN with specified number.

wan vlan wan

[#]

tag

[value]

wan vlan wan

[#] [enable|disable]

wan vlan stat

Syntax Description

Parameter

Description

#

It means the number of WAN interface.

1: means WAN1

2: means WAN2.

value

It means the number to be tagged on packets.

The range of the value is between 32 ~ 4095.

enable|disable

It means to enable or disable the WAN interface for

VLAN.

stat

It means to display the table of WAN VLAN status.

Example

> wan vlan stat

%Interface

Pri

Tag

Enabled

%======================================

% WAN1 (ADSL)

0

% WAN1 (VDSL)

0

%WAN2

0

Telnet Command: wol

This command allows Administrator to set the white list of WAN IP addresses/Subnets, that

the magic packet from these IP addresses/Subnets will be eligible to pass through NAT and

wake up the LAN client. You also need to set NAT rule for LAN client.

wol up

[MAC Address]/[IP Address]

wol fromWan

[on/off/any]

wol fromWan_Setting

[idx][ip address][mask]

Syntax Description

Parameter

Description

MAC Address

It means the MAC address of the host.

Page 784 / 794

Vigor2860 Series User’s Guide

770

IP address

It means the LAN IP address of the host. If you want to

wake up LAN host by using IP address, be sure that that

IP address has been bound with the MAC address (IP

BindMAC).

on/off/any

It means to enable or disable the function of WOL from

WAN.

on: enable

off: disable

any: It means any source IP address can pass through

NAT and wake up the LAN client.

This command will allow the user to choose whether

WoL packets can be passed from the Internet to the

LAN network from a specific WAN interface.

[idx][ip address] [mask]

It means the index number (from 1 to 4).

These commands will allow the user to configure the

LAN clients that the user may wake up from the Internet

through the use of the WoL packet.

ip address -

It means the WAN IP address.

mask -

It means the mask of the IP address.

Example

> wol fromWan on

> wol fromWan_Setting 1 192.168.1.45 255.255.255.0

>

Telnet Command: user

The command is used to create new user account profiles.

User set

[-e|-d|-c|-l|-o|-a|-r|-b]

user edit

[PROFILE_IDX] [-e|-d|-n|-p|-t|-u|-i|-q|-r|-w|-s|-m|-x|-v]

user account

[USER_NAME] [-t|-d|-q|-r|-w]

Syntax Description

Parameter

Description

set

It means to configure general setup for the user

management.

Page 785 / 794

Vigor2860 Series User’s Guide

771

edit

It means to modify the selected user profile.

account

It means to

User Set

-e

Enable User management function.

-d

Disable User management function.

-a[Profile idx][User

name][IP_Address]

It means to pass an IP Address.

Profile idx-

type the index number of the selected profile.

User name

- type the user name that you want it to pass.

IP_Address

- type the IP address that you want it to

pass.

-l all

-l userl

-l ip

Show online user.

all –

all of the users will be displayed on the screen.

user name –

type the user name that you want to view

on the screen.

ip –

type the IP address that you want to view on the

screen.

-o

It means to show user account information.

e.g.,

-o

-c[user name]

-c all

Clear the user record.

user name –

type the user name that you want to get

clear corresponding record.

all –

all of the records will be removed.

-buser [user name]

-b ip [ ip address]

Block specifies user or IP address.

user name –

type the user name that you want to block.

ip address ––

type the IP address that you want to

block.

-u user [user name]

-u ip [ ip address]

Unblock specifies user or IP address.

user name –

type the user name that you want to

unblock.

ip address ––

type the IP address that you want to

Rate

Popular DrayTek Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share