Page 616 / 794
Scroll up to view Page 611 - 615
Vigor2860 Series User’s Guide
602
Telnet Command: ip igmp_proxy
This command allows users to enable/disable igmp proxy server.
ip igmp_proxy
set
ip igmp_proxy
reset
ip igmp_proxy
wan
ip igmp_proxy
t_home[on/off/show/help]
ip igmp_proxy
query
ip igmp_proxy
ppp [0/1]
ip igmp_proxy
status
Syntax Description
Parameter
Description
set
It means to enable proxy server.
reset
It means to disable proxy server.
wan
It means to specify WAN interface for IGMP service.
t_home
It means to specify t_home proxy server for using.
On/off/show/help
It means to turn on/off/display or get more information of
the T_home service.
query
It means to set IGMP general query interval.
The default value is 125000 ms.
ppp
0 – No need to set IGMP with PPP header.
1 – Set IGMP with PPP header.
status
It means to display current status for proxy server.
Example
> ip igmp t_home on
%T-Home Setting:
%T-Home Service is turned on.
%WAN1 : Enabled, connection type: PPPoE, without tag for ADSL
%WAN5 : Enabled, connection type: DHCP, tag: 8
%: PVC4(WAN5) is bound to PVC0(WAN1), protocol=MPoA 1483 Bridge
%IGMP Proxy Interface: WAN5(PVC)
%WAN5 for Router-borne Application/ IPTV on/off: ON
Page 617 / 794
Vigor2860 Series User’s Guide
603
> ip igmp_proxy query 130000
This command is for setting IGMP General Query Interval
The default value is 125000 ms
Current Setting is:130000 ms
>
Page 618 / 794
Vigor2860 Series User’s Guide
604
Telnet Command: ip wanaddr
This command is used to configure WAN IP address.
ip wanaddr
[IP address] ]<IP netmask] [gateway ip]
Syntax Description
Parameter
Description
IP address
Type the IP address for WAN.
IP netmask
Type the net mask for the IP address.
gateway ip
Type the IP address of the gateway.
Example
>
ip wanaddr 172.16.3.221 255.255.0.0 172.16.3.2
% Set WAN IP address OK !!!
Telnet Command: ip wanttr
This command is used to setup the time to return WAN1 from backup WAN.
ip wanttr
[time in seconds]
Syntax Description
Parameter
Description
time in seconds
The available range is 0 ~600 (seconds).
Example
>
ip ip wanttr 500
>
Telnet Command: ip dmz
Specify MAC address of certain device as the DMZ host.
ip dmz
[mac]
Syntax Description
Parameter
Description
mac
It means the MAC address of the device that you want
to specify
Example
>ip dmz ?
Page 619 / 794
Vigor2860 Series User’s Guide
605
% ip dmz <mac>,
now : 00-00-00-00-00-00
> ip dmz 11-22-33-44-55-66
> ip dmz ?
% ip dmz <mac>,
now : 11-22-33-44-55-66
>
Telnet Command: ip session
This command allows users to set maximum session limit number for the specified IP; set
message for exceeding session limit and set how many seconds the IP session block works.
ip session
on
ip session
off
ip session
default [num]
ip session
defaultp2p [num]
ip session
status
ip session
show
ip session
timer [num]
ip session
[block/unblock][IP]
ip session
[add/del][IP1-IP2][num][p2pnum]
Syntax Description
Parameter
Description
on
It means to turn on session limit for each IP.
off
It means to turn off session limit for each IP.
default [num]
It means to set the default number of session num limit.
Defautlp2p [num]
It means to set the default number of session num limit
for p2p.
status
It means to display the current settings.
show
It means to display all session limit settings in the IP
range.
timer [num]
It means to set when the IP session block works.
The unit is second.
[block/unblock][IP]
It means to block/unblock the specified IP address.
Block: The IP cannot access Internet through the router.
Page 620 / 794
Vigor2860 Series User’s Guide
606
Unblock: The specified IP can access Internet through
the router.
add
It means to add the session limits in an IP range.
del
It means to delete the session limits in an IP range.
IP1-IP2
It means the range of IP address specified for this
command.
num
It means the number of the session limits, e.g., 100.
p2pnum
It means the number of the session limits, e.g., 50 for
P2P.
Example
>ip session default 100
> ip session add 192.168.1.5-192.168.1.100 100 50
> ip session on
> ip session status
IP range:
Current ip session limit is turn on
Current default session number is 100
Telnet Command: ip bandwidth
This command allows users to set maximum bandwidth limit number for the specified IP.
ip bandwidth
on
ip bandwidth
off
ip bandwidth
default [tx_rate][rx_rate]
ip bandwidth
status
ip bandwidth
show
ip bandwidth
[add/del] [IP1-IP2][tx][rx][shared]
Syntax Description
Parameter
Description
19216811.live