Page 81 / 335 Scroll up to view Page 76 - 80
Vigor2710 Series User’s Guide
69
Display Name
The caller-ID that you want to be displayed on your friend’s
screen.
Account Number/Name
Enter your account name of SIP Address, e.g. every text
before @.
Authentication ID
Check the box to invoke this function and enter the name or
number used for SIP Authorization with SIP Registrar. If this
setting value is the same as Account Name, it is not necessary
for you to check the box and set any value in this field.
Password
The password provided to you when you registered with a SIP
service.
Expiry Time
The time duration that your SIP Registrar server keeps your
registration record. Before the time expires, the router will
send another register request to SIP Registrar again.
NAT Traversal Support
If the router (e.g.
,
broadband router) you use connects to
internet by other device, you have to set this function for your
necessity.
None –
Disable this function.
Stun
– Choose this option if there is Stun server provided for
your router.
Manual
– Choose this option if you want to specify an
external IP address as the NAT transversal support.
Nortel
– If the soft-switch that you use supports Nortel
solution, you can choose this option.
Ring Port
Set Phone or DECT as the default ring port for this SIP
account. The ports you can set are different based on the
model you have.
Ring Pattern
Choose a ring tone type for the VoIP phone call.
Prefer Codec
Select one of the codecs as the default for your VoIP calls. The
codec used for each call will be negotiated with the peer party
before each session, and so may not be your default choice.
The default codec is G.729A/B; it occupies little bandwidth
while maintaining good voice quality.
If your upstream speed is only 64Kbps, do not use G.711
codec. It is better for you to have at least 256Kbps upstream if
you would like to use G.711.
Page 82 / 335
Vigor2710 Series User’s Guide
70
Single Codec
– If the box is checked, only the selected Codec
will be applied.
Packet Size
The amount of data contained in a single packet. The default
value is 20 ms, which means the data packet will contain 20
ms voice information.
Voice Active Detector
This function can detect if the voice on both sides is active or
not. If not, the router will do something to save the bandwidth
for other using. Click
On
to invoke this function; click
Off
to
close the function.
Page 83 / 335
Vigor2710 Series User’s Guide
71
3.5.3 Phone Settings
This page allows user to set phone settings for Phone 1 and Phone 2 respectively. However,
it changes slightly according to different model you have.
Phone Settings Web Page for Vigor2710 Vn -------
Phone Settings Web Page for Vigor2710 VDn -------
Phone List
Port – Phone, Phone1/Phone2
allow you to set general
settings for PSTN phones. DECT1-6 allow you to set general
settings for DECT phone.
Call Feature
– A brief description for call feature will be
Page 84 / 335
Vigor2710 Series User’s Guide
72
shown in this field for your reference.
Codec
– The default Codec setting for each port will be shown
in this field for your reference. You can click the number
below the Index field to change it for each phone port.
Tone
- Display the tone settings that configured in the
advanced settings page of Phone Index.
Gain
- Display the volume gain settings for Mic/Speaker that
configured in the advanced settings page of Phone Index.
Default SIP Account
– “draytel_1” is the default SIP account.
You can click the number below the Index field to change SIP
account for each phone port.
DTMF Relay
– Display DTMF mode that configured in the
advanced settings page of Phone Index.
Disable Port: Phone
If Phone port is disabled, Phone could not be used anymore.
However, its DSP resource could be used by DECT and DECT
could dial 4 VoIP calls at the same time.
Otherwise, DECT could only dial 3 VoIP calls at the same
time.
DECT phone access code
When registering with DECT phone, you will be asked to type
access code. The default setting in Vigor2710VDn is
1234
.
RTP
Symmetric RTP
– Check this box to invoke the function. To
make the data transmission going through on both ends of
local router and remote router not misleading due to IP lost
(for example, sending data from the public IP of remote router
to the private IP of local router), you can check this box to
solve this problem.
Dynamic RTP Port Start
- Specifies the start port for RTP
stream. The default value is 10050.
Dynamic RTP Port End
- Specifies the end port for RTP
stream. The default value is 15000.
RTP TOS
– It decides the level of VoIP package. Use the
drop down list to choose any one of them.
Page 85 / 335
Vigor2710 Series User’s Guide
73
Detailed Settings for Phone Port
Click the
number link
for Phone/DECT port, you can access into the following page for
configuring Phone settings.
Phone Port Web Page for Vigor2710 Vn -------
DECT Port Web Page for Vigor2710 VDn -------
Hotline
Check the box to enable it. Type in the SIP URL in the field
for dialing automatically when you pick up the phone set.
Session Timer
Check the box to enable the function. In the limited time that
you set in this field, if there is no response, the connecting call
will be closed automatically.
T.38 Fax Function
Check the box to enable the function.
Call Forwarding
There are four options for you to choose.
Disable
is to close
call forwarding function.
Always
means all the incoming calls

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top