Vigor2710 Series User’s Guide

74

will be forwarded into SIP URL without any reason.

Busy

means the incoming calls will be forwarded into SIP URL only

when the local system is busy.

No Answer

means if the

incoming calls do not receive any response, they will be

forwarded to the SIP URL by the time out.

Busy or No

Answer

means if the incoming calls will be forwarded into

SIP URL when the local system is busy or do not receive any

response.

SIP URL

– Type in the SIP URL (e.g., [email protected] or

[email protected]) as the site for call forwarded.

Time Out

– Set the time out for the call forwarding. The

default setting is 30 sec.

DND (Do Not Disturb)

mode

Set a period of peace time without disturbing by VoIP phone

call. During the period, the one who dial in will listen busy

tone, yet the local user will not listen any ring tone.

Index (1-60) in Phone Book -

Enter the index of phone book

profiles. Refer to section

VoIP>>DialPlan>>Phone Book

for

detailed configuration.

CLIR (hide caller ID)

Check this box to hide the caller ID on the display panel of the

phone set.

Call Waiting

Check this box to invoke this function. A notice sound will

appear to tell the user new phone call is waiting for your

response. Click hook flash to pick up the waiting phone call.

Call Transfer

Check this box to invoke this function. Click hook flash to

initiate another phone call. When the phone call connection

succeeds, hang up the phone. The other two sides can

communicate, then.

Default SIP Account

You can set SIP accounts (up to six groups) on SIP Account

page. Use the drop down list to choose one of the profile

names for the accounts as the default one for this phone

setting.

Play dial tone only when account registered -

Check this

box to invoke the function.

In addition, you can press the

Advanced

button to configure tone settings, volume gain,

MISC and DTMF mode.

Advanced

setting is provided for fitting the telecommunication

custom for the local area of the router installed. Wrong tone settings might cause

inconvenience for users. To set the sound pattern of the phone set, simply choose a proper

region to let the system find out the preset tone settings and caller ID type automatically. Or

you can adjust tone settings manually if you choose User Defined. TOn1, TOff1, TOn2 and

TOff2 mean the cadence of the tone pattern. TOn1 and TOn2 represent sound-on; TOff1 and

TOff2 represent the sound-off.

Vigor2710 Series User’s Guide

75

Region

Select the proper region which you are located. The common

settings of

Caller ID Type

,

Dial tone

,

Ringing tone

,

Busy tone

and

Congestion tone

will be shown automatically on the page.

If you cannot find out a suitable one, please choose

User

Defined

and fill out the corresponding values for dial tone,

ringing tone, busy tone, and congestion tone by yourself for

VoIP phone.

Also, you can specify each field for your necessity. It is

recommended for you to use the default settings for VoIP

communication.

Volume Gain

Mic Gain (1-10)/Speaker Gain (1-10)

- Adjust the volume of

microphone and speaker by entering number from 1- 10. The

larger of the number, the louder the volume is.

Vigor2710 Series User’s Guide

76

MISC

Dial Tone Power Leve

l - This setting is used to adjust the

loudness of the dial tone. The smaller the number is, the louder

the dial tone is.

It is recommended for you to use the default

setting.

Ring Frequency

- This setting is used to drive the frequency of

the ring tone. It is recommended for you to use the default

setting. Notice that such setting is not available for DECT phone

port.

DTMF

DTMF Mode –

There are four DTMF modes for you to choose.

InBand

-

Choose this one then the Vigor will send the DTMF

tone as audio directly when you press the keypad on the phone.

OutBand

-

Choose this one then the Vigor will capture the

keypad number you pressed and transform it to digital form then

send to the other side; the receiver will generate the tone

according to the digital form it receive. This function is very

useful when the network traffic congestion occurs and it still can

remain the accuracy of DTMF tone.

SIP INFO

-

Choose this one then the Vigor will capture the

DTMF tone and transfer it into SIP form. Then it will be sent to

the remote end with SIP message.

Payload Type (rfc2833)

- Choose a number from 96 to 127, the

default value was 101. This setting is available for the OutBand

(RFC2833) mode.

Vigor2710 Series User’s Guide

77

3.5.4 DECT

From this page, you can enable register or deregister handsets for using DECT function.

Refresh Seconds

Specify the interval of refresh time to obtain the latest VoIP

calling information. The information will update immediately

when the

Refresh

button is clicked.

Handset

After DECT phone registered with router, it would be assigned

one unique handset ID.

Status

It is used to indicate the DECT handset status. For example, if

you have registered with router DECT module, you would get –

F00_REGISTERED_IDLE

. If you get one incoming call for

this DECT handset, you would see -

F07_CALL_RECEIVED.

PCM Channel

This field can distinguish which PCM channel is used by

the handset. 255 (default setting) means it is idle and voice data

is not transferred through any PCM channel.

Deregister Handset

If your handset has registered to the router, you could use this

button to deregister it from router.

Wideband Voice

Check this box to enable the function to avoid hearing noisy

voice.

Ring Handset

Check this box to enable the function.

DECT phone access

mode

When registering with DECT phone, you will be asked to type

access code. The default setting in Vigor2710VDn is

1234

.

Enable Registration

Mode

If you want to use handset to register with the router, you need

to enable DECT module registration mode via this button.

Otherwise, you can't search our DECT base station from the air.

Vigor2710 Series User’s Guide

78

Deregister All Handset

Deregister all registered handset.

Example

Vigor 2710 VDn provides a DECT GAP/CAT-iq base module, which can facilitate 4

simultaneous wireless audio connections and 6 phone registration.

1.

Open

VoIP>>DECT

.

Note:

DECT menu will appear if DECT module is detected.

2.

In the web page, please click

Enable Registration Mode

and wait for DECT handset

to register.

3.

When the registration is finished, open

VoIP>>SIP Accounts

. The Registered DECT

phone will be available for you to choose. Choose the one you need.