Vigor2710 Series User’s Guide

69

Display Name

The caller-ID that you want to be displayed on your friend’s

screen.

Account Number/Name

Enter your account name of SIP Address, e.g. every text

before @.

Authentication ID

Check the box to invoke this function and enter the name or

number used for SIP Authorization with SIP Registrar. If this

setting value is the same as Account Name, it is not necessary

for you to check the box and set any value in this field.

Password

The password provided to you when you registered with a SIP

service.

Expiry Time

The time duration that your SIP Registrar server keeps your

registration record. Before the time expires, the router will

send another register request to SIP Registrar again.

NAT Traversal Support

If the router (e.g.

,

broadband router) you use connects to

internet by other device, you have to set this function for your

necessity.

None –

Disable this function.

Stun

– Choose this option if there is Stun server provided for

your router.

Manual

– Choose this option if you want to specify an

external IP address as the NAT transversal support.

Nortel

– If the soft-switch that you use supports Nortel

solution, you can choose this option.

Ring Port

Set Phone or DECT as the default ring port for this SIP

account. The ports you can set are different based on the

model you have.

Ring Pattern

Choose a ring tone type for the VoIP phone call.

Prefer Codec

Select one of the codecs as the default for your VoIP calls. The

codec used for each call will be negotiated with the peer party

before each session, and so may not be your default choice.

The default codec is G.729A/B; it occupies little bandwidth

while maintaining good voice quality.

If your upstream speed is only 64Kbps, do not use G.711

codec. It is better for you to have at least 256Kbps upstream if

you would like to use G.711.

Vigor2710 Series User’s Guide

70

Single Codec

– If the box is checked, only the selected Codec

will be applied.

Packet Size

The amount of data contained in a single packet. The default

value is 20 ms, which means the data packet will contain 20

ms voice information.

Voice Active Detector

This function can detect if the voice on both sides is active or

not. If not, the router will do something to save the bandwidth

for other using. Click

On

to invoke this function; click

Off

to

close the function.

Vigor2710 Series User’s Guide

71

3.5.3 Phone Settings

This page allows user to set phone settings for Phone 1 and Phone 2 respectively. However,

it changes slightly according to different model you have.

Phone Settings Web Page for Vigor2710 Vn -------

Phone Settings Web Page for Vigor2710 VDn -------

Phone List

Port – Phone, Phone1/Phone2

allow you to set general

settings for PSTN phones. DECT1-6 allow you to set general

settings for DECT phone.

Call Feature

– A brief description for call feature will be

Vigor2710 Series User’s Guide

72

shown in this field for your reference.

Codec

– The default Codec setting for each port will be shown

in this field for your reference. You can click the number

below the Index field to change it for each phone port.

Tone

- Display the tone settings that configured in the

advanced settings page of Phone Index.

Gain

- Display the volume gain settings for Mic/Speaker that

configured in the advanced settings page of Phone Index.

Default SIP Account

– “draytel_1” is the default SIP account.

You can click the number below the Index field to change SIP

account for each phone port.

DTMF Relay

– Display DTMF mode that configured in the

advanced settings page of Phone Index.

Disable Port: Phone

If Phone port is disabled, Phone could not be used anymore.

However, its DSP resource could be used by DECT and DECT

could dial 4 VoIP calls at the same time.

Otherwise, DECT could only dial 3 VoIP calls at the same

time.

DECT phone access code

When registering with DECT phone, you will be asked to type

access code. The default setting in Vigor2710VDn is

1234

.

RTP

Symmetric RTP

– Check this box to invoke the function. To

make the data transmission going through on both ends of

local router and remote router not misleading due to IP lost

(for example, sending data from the public IP of remote router

to the private IP of local router), you can check this box to

solve this problem.

Dynamic RTP Port Start

- Specifies the start port for RTP

stream. The default value is 10050.

Dynamic RTP Port End

- Specifies the end port for RTP

stream. The default value is 15000.

RTP TOS

– It decides the level of VoIP package. Use the

drop down list to choose any one of them.

Vigor2710 Series User’s Guide

73

Detailed Settings for Phone Port

Click the

number link

for Phone/DECT port, you can access into the following page for

configuring Phone settings.

Phone Port Web Page for Vigor2710 Vn -------

DECT Port Web Page for Vigor2710 VDn -------

Hotline

Check the box to enable it. Type in the SIP URL in the field

for dialing automatically when you pick up the phone set.

Session Timer

Check the box to enable the function. In the limited time that

you set in this field, if there is no response, the connecting call

will be closed automatically.

T.38 Fax Function

Check the box to enable the function.

Call Forwarding

There are four options for you to choose.

Disable

is to close

call forwarding function.

Always

means all the incoming calls