Page 26 / 241
Scroll up to view Page 21 - 25
Vigor2130 Series User’s Guide
18
2.4 Quick Start Wizard
Notice:
Quick Start Wizard for user mode operation is the same as for admin
mode operation.
If your router can be under an environment with high speed NAT, the configuration provide
here can help you to deploy and use the router quickly. The first screen of
Quick Start
Wizard
is welcome page, please click
Next
.
2.4.1 Setting up the Password
The first screen of
Quick Start Wizard
is entering login password. After typing the password,
please click
Next
.
Page 27 / 241
Vigor2130 Series User’s Guide
19
2.4.2 Setting up the Time Zone
On the next page as shown below, please select the Time Zone for the router installed and
specify the NTP server(s). Then click
Next
for next step.
2.4.3 Setting up the Internet Connection
On the next page as shown below, please select the appropriate connection type according to
the information from your ISP. There are five types offered in this page. Each connection type
will bring out different web page.
Page 28 / 241
Vigor2130 Series User’s Guide
20
Static IP
You will receive a fixed public IP address or a public subnet, namely multiple public IP
addresses from your DSL or Cable ISP service providers. In most cases, a Cable service
provider will offer a fixed public IP, while a DSL service provider will offer a public subnet.
If you have a public subnet, you could assign an IP address or many IP address to the WAN
interface.
IP Address
Type the IP address.
Subnet Mask
Type the subnet mask.
Gateway
Type the gateway IP address.
Primary DNS Server
Type in the primary IP address for the router
Secondary DNS Server
Type in secondary IP address for necessity in the future.
Enable
The router will detect the MAC address automatically. Or,
check the box to enable MAC address cloning.
Clone MAC Address
It is available when the box of Enable is checked. Click Clone
PC Address. The result will be displayed in the field of MAC
Address.
After finishing the settings here, please click
Next.
Page 29 / 241
Vigor2130 Series User’s Guide
21
DHCP
It is not necessary for you to type any IP address manually. Simply choose this type and the
system will obtain the IP address automatically from DHCP server.
Enable
The router will detect the MAC address automatically. Or,
check the box to enable MAC address cloning.
Clone MAC Address
It is available when the box of Enable is checked. Click Clone
PC Address. The result will be displayed in the field of MAC
Address.
After finishing the settings here, please click
Next.
PPPoE
PPPoE stands for
Point-to-Point Protocol over Ethernet
. It relies on two widely accepted
standards: PPP and Ethernet. It connects users through an Ethernet to the Internet with a
common broadband medium, such as a single DSL line, wireless device or cable modem. All
the users over the Ethernet can share a common connection.
PPPoE is used for most of DSL modem users. All local users can share one PPPoE connection
for accessing the Internet. Your service provider will provide you information about user name,
password, and authentication mode.
Page 30 / 241
Vigor2130 Series User’s Guide
22
If your ISP provides you the
PPPoE
connection, please select
PPPoE
for this router. The
following page will be shown:
User Name
Assign a specific valid user name provided by the ISP.
Password
Assign a valid password provided by the ISP.
Redial Policy
If you want to connect to Internet all the time, you can choose
Always On
. Otherwise, choose
Connect on Demand
.
Idle Time Out
Set the timeout for breaking down the Internet after passing
through the time without any action. The unit is seconds. The
range is XX ~ XX.
MTU Size
It means Max Transmit Unit for packet. The default
setting is 1442.
Enable
The router will detect the MAC address automatically. Or,
check the box to enable MAC address cloning.
Clone MAC Address
It is available when the box of Enable is checked. Click Clone
PC Address. The result will be displayed in the field of MAC
Address.
After finishing the settings here, please click
Next.
19216811.live