1. Home
    2. /
  2. Manuals
    3. /
  3. DrayTek
    4. /
  4. Vigor-2130
    5. /
  5. 20
Page 96 / 241 Scroll up to view Page 91 - 95
Vigor2130 Series User’s Guide
88
DHCPv6 Client (IA_NA)
DHCPv6 client mode would use IA_NA option of DHCPv6 protocol to obtain IPv6 address
from server.
Primary DNS Server
Type primary DNS Server address here.
Secondary DNS Server
Type secondary DNS Server address here
DHCPv6 Client (IA_PD)
DHCPv6 client mode would use IA_PA option of DHCPv6 protocol to obtain IPv6 prefix
from server.
TSPC
Tunnel setup protocol client (TSPC) is an application which could help you to connect to IPv6
network easily.
Please make sure your IPv4 WAN connection is OK and apply one free account from hexage
(http://go6.net/4105/register.asp
) before you try to use TSPC for network connection. TSPC
would connect to tunnel broker and requests a tunnel according to the specifications inside the
configuration file. It gets a public IPv6 IP address and an IPv6 prefix from the tunnel broker
and then monitors the state of the tunnel in background.
After getting the IPv6 prefix and starting router advertisement daemon (RADVD), the PC
behind this router can directly connect to IPv6 the Internet.
Page 97 / 241
Vigor2130 Series User’s Guide
89
Username
Type the name obtained from the broker. “vigor2130” is a
default username applied from
http://go6.net/4105/register.asp
. It is suggested for you to
apply another username and password.
Password
Type the password assigned with the user name.
Confirm Password
Type the password again to make the confirmation.
Tunnel Broker
Type the address
for the tunnel broker IP, FQDN or an
optional port number.
Tunnel Mode
IPv6-in-IPv4 Tunnel
- Let the broker choose the tunnel
mode appropriate for the client.
IPv6-in-IPv4 (Native)
- Request an IPv6 in IPv4 tunnel.
IPv6-in-IPv4 (NAT Traversal
- Request an IPv6 in UDP
of IPv4 tunnel (for clients behind a NAT).
Auto-reconnect Delay
After passing the time set here, the client will retry to
connect in case of failure or keepalive timeout.
0 means not retry.
Keepalive
Yes
– Keep the connection between TSPC and tunnel
broker always on. TSPC will send ping packet to make
sure the connection between both ends is normal.
No
- The client will not send keepalives.
Keepalive_interval
Type the time for the interval between two keepalive
messages transferring from the client to the broker.
Page 98 / 241
Vigor2130 Series User’s Guide
90
Prefixlen
Type the required prefix length for the client network.
If_prefix
Display LAN interface name.
The name of the OS
interface that will be configured with the first 64 of
the received prefix from the broker and the router
advertisement daemon is started to advertise that
prefix on the if_prefix interface.
3.8.2 IPv6 LAN Setup
This page defines the IPv6 connection types for LAN interface. Possible types contain
DHCPv6 and RADVD. Each type requires different parameter settings.
IPv6 Address
Type static IPv6 address for LAN.
IPv6 Link_local Address
It is used for communicating with neighbouring nodes on
the same link. It is defined by the address prefix fe80::/10.
You don't need to setup Link-Local address manually for it
is generated automatically according to your MAC
Address.
Enable Autoconfiguration
Check this box to enable the auto-configuration function
for IPv6 connection.
Configuration Type
Vigor2130 provides 2 daemons for LAN side IPv6 address
configuration. One is
RADVD
(stateless) and the other is
DHCPv6 Server
(Stateful).
DHCPv6 Server
- DHCPv6 Server could assign IPv6
address to PC according to the Start/End IPv6 address
configuration.
IPv6 Start Address/IPv6 End Address
- Type the start and
end address for IPv6 server.
Page 99 / 241
Vigor2130 Series User’s Guide
91
RADVD -
The router advertisement daemon (radvd) sends
Router Advertisement messages, specified by RFC 2461,
to a local Ethernet LAN periodically and when requested
by a node sending a Router Solicitation message. These
messages are required for IPv6 stateless autoconfiguration.
Advertisement Lifetime
-
The lifetime associated with
the default router in units of seconds. It's used to control
the lifetime of the prefix. The maximum value corresponds
to 18.2 hours. A lifetime of 0 indicates that the router is not
a default router and should not appear on the default router
list.
3.8.3 IPv6 Firewall Setup
This page allows users to set firewall for the protocol of IPv6.
Note
: Section 4.4
Firewall
is configured for IPv4 packets only.
Name
Display the name of the rule.
Protocol
Display the protocol (TCP/UDP/ICMPv6) the rule uses.
Source IP
Display the source IP address of such rule.
Destination IP
Display the destination IP address of such rule.
Source Port
Display the source port number of such rule.
Destination Port
Display the destination port number of such rule.
Action
Display the status (accept or drop) of such rule.
Page 100 / 241
Vigor2130 Series User’s Guide
92
Adding a New Rule
Click
Add New Rule
to configure a new rule for IPv6 Firewall.
Note:
You can set up to 20 sets of IPv6 rules.
Name
Type a name for the rule.
Protocol
Specify a protocol for this rule.
Source IP Type
Determine the IP type as the source.
Source IP
Type the IP address here if you choose
Single
as
Source
IP Type
.
Source Subnet
Type the subnet mask here if you choose
Subnet
as
Source IP Type
.
Destination IP Type
Determine the IP type as the destination.
Destination IP
Type the IP address here if you choose
Single
as
Destination IP Type
.

Rate

4.3 / 5 based on 3 votes.

Popular DrayTek Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top