1. Home
    2. /
  2. Manuals
    3. /
  3. DrayTek
    4. /
  4. Vigor-2110
    5. /
  5. 15
Page 71 / 275 Scroll up to view Page 66 - 70
Vigor2110 Series User’s Guide
64
In addition, you can press the
Advanced
button to configure tone settings, volume gain, MISC
and DTMF mode.
Advanced
setting is provided for fitting the telecommunication custom for
the local area of the router installed. Wrong tone settings might cause inconvenience for users.
To set the sound pattern of the phone set, simply choose a proper region to let the system find
out the preset tone settings and caller ID type automatically. Or you can adjust tone settings
manually if you choose User Defined. TOn1, TOff1, TOn2 and TOff2 mean the cadence of the
tone pattern. TOn1 and TOn2 represent sound-on; TOff1 and TOff2 represent the sound-off.
Region
Select the proper region which you are located. The common
settings of
Caller ID Type
,
Dial tone
,
Ringing tone
,
Busy
tone
and
Congestion tone
will be shown automatically on the
page. If you cannot find out a suitable one, please choose
User
Defined
and fill out the corresponding values for dial tone,
ringing tone, busy tone, congestion tone by yourself for VoIP
phone.
Page 72 / 275
Vigor2110 Series User’s Guide
65
Also, you can specify each field for your necessity. It is
recommended for you to use the default settings for VoIP
communication.
Volume Gain
Mic Gain (1-10)/Speaker Gain (1-10)
- Adjust the volume of
microphone and speaker by entering number from 1- 10. The
larger of the number, the louder the volume is.
MISC
Dial Tone Power Leve
l - This setting is used to adjust the
loudness of the dial tone. The smaller the number is, the louder
the dial tone is.
It is recommended for you to use the default
setting.
Ring Frequency
- This setting is used to drive the frequency of
the ring tone. It is recommended for you to use the default
setting.
DTMF
DTMF Mode –
There are four DTMF modes for you to choose.
InBand
-
Choose this one then the Vigor will send the DTMF
tone as audio directly when you press the keypad on the phone
OutBand
-
Choose this one then the Vigor will capture the
keypad number you pressed and transform it to digital form
then send to the other side; the receiver will generate the tone
according to the digital form it receive. This function is very
useful when the network traffic congestion occurs and it still
can remain the accuracy of DTMF tone.
SIP INFO
-
Choose this one then the Vigor will capture the
DTMF tone and transfer it into SIP form. Then it will be sent to
the remote end with SIP message.
Payload Type (rfc2833)
- Choose a number from 96 to 127,
the default value was 101. This setting is available for the
OutBand (RFC2833) mode.
3.5.4 Status
From this page, you can find codec, connection and other important call status for each port.
Page 73 / 275
Vigor2110 Series User’s Guide
66
Refresh Seconds
Specify the interval of refresh time to obtain the latest VoIP
calling information. The information will update immediately
when the Refresh button is clicked.
Port
It shows current connection status for the port of Phone1 and
Phone2.
Status
It shows the VoIP connection status.
IDLE -
Indicates that the VoIP function is idle.
HANG_UP -
Indicates that the connection is not established
(busy tone).
CONNECTING -
Indicates that the user is calling out.
WAIT_ANS -
Indicates that a connection is launched and
waiting for remote user’s answer.
ALERTING -
Indicates that a call is coming.
ACTIVE-
Indicates that the VoIP connection is launched.
Codec
Indicates the voice codec employed by present channel.
PeerID
The present in-call or out-call peer ID (the format may be IP or
Domain).
Elapse
The format is represented as hours:minutes:seconds.
Tx Pkts
Total number of transmitted voice packets during this
connection session.
Rx Pkts
Total number of received voice packets during this connection
session.
Rx Losts
Total number of lost packets during this connection session.
Rx Jitter
The jitter of received voice packets.
Page 74 / 275
Vigor2110 Series User’s Guide
67
In Calls
Accumulation for the times of in call.
Out Calls
Accumulation for the times of out call.
Miss Calls
Accumulation for the times of missing call.
Speaker Gain
The volume of present call.
Log
Display logs of VoIP calls.
3.6 Wireless LAN
This function is used for “n” models.
3.6.1 Basic Concepts
Over recent years, the market for wireless communications has enjoyed tremendous growth.
Wireless technology now reaches or is capable of reaching virtually every location on the
surface of the earth. Hundreds of millions of people exchange information every day via
wireless communication products. The Vigor “n” model, a.k.a. Vigor wireless router, is
designed for maximum flexibility and efficiency of a small office/home. Any authorized staff
can bring a built-in WLAN client PDA or notebook into a meeting room for conference
without laying a clot of LAN cable or drilling holes everywhere. Wireless LAN enables high
mobility so WLAN users can simultaneously access all LAN facilities just like on a wired
LAN as well as Internet access
The Vigor wireless routers are equipped with a wireless LAN interface compliant with the
standard IEEE 802.11n draft 2 protocol. To boost its performance further, the Vigor Router is
also loaded with advanced wireless technology to lift up data rate up to 300 Mbps*. Hence,
you can finally smoothly enjoy stream music and video.
Note
:
*
The actual data throughput will vary according to the network conditions and
environmental factors, including volume of network traffic, network overhead and
building materials.
In an Infrastructure Mode of wireless network, Vigor wireless router plays a role as an Access
Point (AP) connecting to lots of wireless clients or Stations (STA). All the STAs will share the
same Internet connection via Vigor wireless router. The
General Settings
will set up the
information of this wireless network, including its SSID as identification, located channel etc.
Page 75 / 275
Vigor2110 Series User’s Guide
68
Security Overview
Real-time Hardware Encryption:
Vigor Router is equipped with a hardware AES encryption
engine so it can apply the highest protection to your data without influencing user experience.
Complete Security Standard Selection:
To ensure the security and privacy of your wireless
communication, we provide several prevailing standards on market.
WEP (Wired Equivalent Privacy) is a legacy method to encrypt each frame transmitted via
radio using either a 64-bit or 128-bit key. Usually access point will preset a set of four keys
and it will communicate with each station using only one out of the four keys.
WPA (Wi-Fi Protected Access), the most dominating security mechanism in industry, is
separated into two categories: WPA-personal or called WPA Pre-Share Key (WPA/PSK), and
WPA-Enterprise or called WPA/802.1x.
In WPA-Personal, a pre-defined key is used for encryption during data transmission. WPA
applies Temporal Key Integrity Protocol (TKIP) for data encryption while WPA2 applies AES.
The WPA-Enterprise combines not only encryption but also authentication.
Since WEP has been proved vulnerable, you may consider using WPA for the most secure
connection. You should select the appropriate security mechanism according to your needs.
No matter which security suite you select, they all will enhance the over-the-air data
protection and /or privacy on your wireless network. The Vigor wireless router is very flexible
and can support multiple secure connections with both WEP and WPA at the same time.
Separate the Wireless and the Wired LAN- WLAN Isolation
enables you to isolate your
wireless LAN from wired LAN for either quarantine or limit access reasons. To isolate means
neither of the parties can access each other. To elaborate an example for business use, you
may set up a wireless LAN for visitors only so they can connect to Internet without hassle of
the confidential information leakage. For a more flexible deployment, you may add filters of
MAC addresses to isolate users’ access from wired LAN.
Manage Wireless Stations - Station List
will display all the station in your wireless network
and the status of their connection.
Below shows the menu items for Wireless LAN.
3.6.2 General Setup
By clicking the
General Settings
, a new web page will appear so that you could configure the
SSID and the wireless channel. Please refer to the following figure for more information.

Rate

4.7 / 5 based on 3 votes.

Popular DrayTek Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top