Page 31 / 357
Scroll up to view Page 26 - 30
Vigor2830 Series User’s Guide
19
WAN1, WAN2 and WAN3 will bring up different configuration page. Refer to the following
for detailed information.
2.4.1 For WAN1
Choose WAN1 and click
Next
to display the following page. Please select the appropriate
Internet access type
according to the information from your ISP
. For example, you should
select PPPoE mode if the ISP provides you PPPoE interface. Then click
Next
for next step.
Page 32 / 357
Vigor2830 Series User’s Guide
20
2.4.1.1 PPPoE
PPPoE/PPPoA:
PPPoE stands for
Point-to-Point Protocol over Ethernet
. It relies on two
widely accepted standards: PPP and Ethernet. It connects users through an Ethernet to the
Internet with a common broadband medium, such as a single DSL line, wireless device or
cable modem. All the users over the Ethernet can share a common connection.
PPPoE is used for most of DSL modem users. All local users can share one PPPoE connection
for accessing the Internet. Your service provider will provide you information about user name,
password, and authentication mode.
If you click PPPoE or PPPoA as the protocol, please manually enter the Username/Password
provided by your ISP. Then click
Next
.
User Name
Assign a specific valid user name provided by the
ISP.
Password
Assign a valid password provided by the ISP.
Confirm Password
Retype the password.
Click
Next
for viewing summary of such connection.
Page 33 / 357
Vigor2830 Series User’s Guide
21
Click
Finish.
A page of
Quick Start Wizard Setup OK!!!
will appear.
Then, the system
status of this protocol will be shown.
Now, you can enjoy surfing on the Internet.
2.4.1.1 1483 Bridged IP /1483 Routed IP
If you choose 1483 Bridged IP / 1483 Routed IP as the protocol, you will get the following
page. Please type in the IP address information originally provided by your ISP. Then click
Next
for next step.
Now you can see the following screen. It indicates that the setup is complete. Different types
of connection modes will have different summary.
Page 34 / 357
Vigor2830 Series User’s Guide
22
Click
Finish.
A page of
Quick Start Wizard Setup OK!!!
will appear.
Then, the system
status of this protocol will be shown.
Now, you can enjoy surfing on the Internet.
2.4.2 For WAN2
WAN2 is dedicated to physical mode in Ethernet. If you choose WAN2, please specify
physical type. Then, click
Next
.
On the next page as shown below, please select the appropriate Internet access type according
to the information from your ISP. For example, you should select PPPoE mode if the ISP
provides you PPPoE interface. Then click
Next
for next step.
Page 35 / 357
Vigor2830 Series User’s Guide
23
2.4.2.1 PPPoE
PPPoE stands for
Point-to-Point Protocol over Ethernet
. It relies on two widely accepted
standards: PPP and Ethernet. It connects users through an Ethernet to the Internet with a
common broadband medium, such as a single DSL line, wireless device or cable modem. All
the users over the Ethernet can share a common connection.
PPPoE is used for most of DSL modem users. All local users can share one PPPoE connection
for accessing the Internet. Your service provider will provide you information about user name,
password, and authentication mode.
If you click PPPoE as the protocol, please manually enter the Username/Password provided by
your ISP. Then click
Next
.
User Name
Assign a specific valid user name provided by the ISP.
Password
Assign a valid password provided by the ISP.
Confirm Password
Retype the password.
Click
Next
for viewing summary of such connection.
19216811.live