Page 36 / 78 Scroll up to view Page 31 - 35
36
D-Link WBR-2310 User Manual
Section 3 - Configuration
To use the Universal Plug and Play (UPnP
)
feature click on
Enabled
. UPNP provides
compatibility with networking equipment, software
and peripherals.
Unchecking the box will not allow the WBR-2310
to respond to pings. Blocking the Ping may provide
some extra security from hackers. Check the box
to allow the WAN port to be “pinged”.
You may set the port speed of the WAN port to
10Mbps, 100Mbps, or auto. Some older cable
or DSL modems may require you to set the port
speed to 10Mbps.
Gaming mode allows a form of pass-through for
certain Internet Games. If you are using Xbox,
Playstation2 or a PC, make sure you are using the
latest firmware and Gaming Mode is enabled. To
utilize Gaming Mode, click the box. If you are not
using a Gaming application, it is recommended
that you Disable Gaming Mode.
Check the box to allow multicast traffic to pass
through the router from the Internet.
UPnP Settings:
WAN Ping:
WAN select to
10/100 Mbps:
Gaming Mode:
Multicast
streams:
Advanced Network Settings
Page 37 / 78
37
D-Link WBR-2310 User Manual
Section 3 - Configuration
Enter a new Login Name for the Administrator
account.
Enter a new password for the Administrator Login
Name. The administrator can make changes to
the settings.
Enter a new Login Name for the User account.
Enter the new password for the User login. If you
login as the User, you can only see the settings,
but cannot change them.
Remote management allows the WBR-2310
to be configured from the Internet by a web
browser. A username and password is still
required to access the Web-Management
interface. In general, only a member of your
network can browse the built-in web pages to
perform Administrator tasks. This feature enables
you to perform Administrator tasks from the
remote (Internet) host.
The Internet IP address of the computer that has
access to the Broadband Router. If you input an
asterisk (*) into this field, then any computer will
be able to access the Router. Putting an asterisk (*) into this field would present a security risk and is not recommended.
The port number used to access the WBR-2310.
Example: http://x.x.x.x:8080 whereas x.x.x.x is the WAN IP address of the WBR-2310 and 8080 is the port used for the Web
Management interface.
Administrator
Login Name:
Administrator
Password:
User Login Name:
User Password:
Remote
Management:
IP Address:
Port:
Administrator Settings
This page will allow you to change the Administrator and User passwords. You can also enable Remote Management.
There are two accounts that can access the management interface through the web browser. The accounts are admin
and user. Admin has read/write access while user has read-only access. User can only view the settings but cannot
make any changes. Only the admin account has the ability to change both admin and user account passwords.
Page 38 / 78
38
D-Link WBR-2310 User Manual
Section 3 - Configuration
Time Settings
Select the Time Zone from the drop-down
menu.
To select Daylight Saving time manually, select
enabled or disabled, and enter a start date and
an end date for daylight saving time.
NTP is short for Network Time Protocol. NTP
synchronizes computer clock times in a network
of computers. This field is optional.
To manually input the time, enter the values
in these fields for the Year, Month, Day, Hour,
Minute, and Second. Click Set Time. You can also
click Copy Your Computer’s Time Settings.
Time Zone:
Daylight Saving:
Automatic:
Manual:
Page 39 / 78
39
D-Link WBR-2310 User Manual
Section 3 - Configuration
Use this option to save the current router
configuration settings to a file on the hard disk
of the computer you are using. First, click the
Save button. You will then see a file dialog,
where you can select a location and file name
for the settings.
Use this option to load previously saved
router configuration settings. First, use the
Browse control to find a previously save file
of configuration settings. Then, click the Load
button to transfer those settings to the router.
This option will restore all configuration settings
back to the settings that were in effect at the
time the router was shipped from the factory.
Any settings that have not been saved will be
lost, including any rules that you have created. If
you want to save the current router configuration
settings, use the Save button above.
Click Enabled to use the JumpStart function.
If your wireless router uses JumpStart, please
check the adapter for instructions.
Use this option to reset the JumpStart feature.
Save Settings to
Local Hard Drive:
Load Settings
from Local Hard
Drive:
Restore to Factory
Default Settings:
JumpStart
function:
Reset JumpStart:
System Settings
Page 40 / 78
40
D-Link WBR-2310 User Manual
Section 3 - Configuration
Click on the link in this screen to find out if there
is an updated firmware; if so, download the new
firmware to your hard drive.
After you have downloaded the new firmware,
click Browse in this window to locate the
firmware update on your hard drive.
Click
Save
Settings
to complete the firmware upgrade.
Firmware
Upgrade:
Browse:
Update Firmware
You can upgrade the firmware of the Router here. Make sure the firmware you want to use is on the local hard drive of
the computer. Click on
Browse
to locate the firmware file to be used for the update. Please check the D-Link support
site for firmware updates at http://support.dlink.com. You can download firmware upgrades to your hard drive from the
D-Link support site.

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top