D-Link WBR-2310v2 Router Manual PDF (Setup & Configuration Guide)

Page 16 / 78 Scroll up to view Page 11 - 15

16

D-Link WBR-2310 User Manual

Section 3 - Conﬁguration

Click

Create a new password and then click

Select your time zone from the drop-down menu and then click

Select the type of Internet connection you use and then click

Page 17 / 78

17

D-Link WBR-2310 User Manual

Section 3 - Conﬁguration

If you selected Dynamic, you may need to enter the MAC address of the

computer that was last connected directly to your modem. If you are currently

using that computer, click

Clone Your PC’s MAC Address

and then click

The Host Name is optional but may be required by some ISPs. The default

host name is the device name of the Router and may be changed.

If you selected PPPoE, enter your PPPoE username and password. Click

Select

Static

if your ISP assigned you the IP address, subnet mask, gateway,

and DNS server addresses.

Note:

Make sure to remove your PPPoE software from your computer. The

software is no longer needed and will not work through a router.

If you selected PPTP, enter your PPTP username and password. Click

Page 18 / 78

18

D-Link WBR-2310 User Manual

Section 3 - Conﬁguration

If you selected L2TP, enter your L2TP username and password. Click

If you selected Static, enter your network settings supplied by your Internet

provider. Click

Click Connect to save your settings. Once the router is ﬁnished rebooting,

click Continue. Please allow 1-2 minutes to connect.

Close your browser window and reopen it to test your Internet connection.

It may take a few tries to initially connect to the Internet.

Page 19 / 78

19

D-Link WBR-2310 User Manual

Section 3 - Conﬁguration

Choose Dynamic IP Address to obtain IP Address

information automatically from your ISP. Select

this option if your ISP does not give you any IP

numbers to use. This option is commonly used

for Cable modem services.

The Host Name is optional but may be required by

some ISPs. The default host name is the device

name of the Router and may be changed.

The default MAC Address is set to the WAN’s

physical interface MAC address on the Broadband

Router. It is not recommended that you change

the default MAC address unless required by your

ISP.

The default MAC address is set to the WAN’s

physical interface MAC address on the Broadband

Router. You can use the “Clone MAC Address”

button to copy the MAC address of the Ethernet

Card installed by your ISP and replace the WAN

MAC address with the MAC address of the router.

It is not recommended that you change the default

MAC address unless required by your ISP.

Enter the Primary DNS server IP address assigned by your ISP.

Maximum Transmission Unit - you may need to change the MTU for optimal performance with your speciﬁc ISP. 1500 is the

default MTU.

Dynamic IP

Address:

Host Name:

MAC Address:

Internet Setup

Dynamic (Cable)

Clone MAC

Address:

DNS Addresses:

MTU:

Page 20 / 78

20

D-Link WBR-2310 User Manual

Section 3 - Conﬁguration

Select

Dynamic

(most common) or

Static

. Select

Static

if your ISP assigned you the IP address, subnet mask,

gateway, and DNS server addresses.

Enter your PPPoE user name.

Enter your PPPoE password and then retype the password

in the next box.

Enter the ISP Service Name (optional).

Enter the IP address (Static PPPoE only).

Enter the Primary and Secondary DNS Server Addresses

(Static PPPoE only).

Enter a maximum idle time during which the Internet

connection is maintained during inactivity. To disable this

feature, enable Auto-reconnect.

Maximum Transmission Unit - you may need to change the

MTU for optimal performance with your speciﬁc ISP. 1492

is the default MTU.

Select either Always-on, Manual, or Connect-on demand.

PPPoE:

User Name:

Password:

Service Name:

IP Address:

DNS Addresses:

Maximum Idle

Time:

MTU:

Connection Mode

Select:

Internet Setup

PPPoE (DSL)

Choose PPPoE (Point to Point Protocol over Ethernet) if your ISP uses a PPPoE connection. Your ISP will provide

you with a username and password. This option is typically used for DSL services. Make sure to remove your PPPoE

software from your computer. The software is no longer needed and will not work through a router.

Rate

Popular D-Link Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share