D-Link WBR-2310 Router Manual PDF (Setup & Configuration Guide)

Page 21 / 78 Scroll up to view Page 16 - 20

21

D-Link WBR-2310 User Manual

Section 3 - Conﬁguration

Select

Dynamic

(most common) or

Static

. Select

Static

if your ISP

assigned you the IP address, subnet mask, gateway, and DNS server

addresses.

Enter the IP address (Static PPTP only).

Enter the Primary and Secondary DNS Server Addresses (Static

PPTP only).

Enter the Gateway IP Address provided by your ISP.

The DNS server information will be supplied by your ISP (Internet

Service Provider.)

Enter the Server IP provided by your ISP (optional).

Enter your PPTP account name.

Enter your PPTP password and then retype the password in the next

box.

Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable

Auto-reconnect.

Maximum Transmission Unit - you may need to change the MTU for optimal performance with your speciﬁc ISP. 1492 is the

default MTU.

Select either Always-on, Manual, or Connect-on demand.

PPTP:

IP Address:

Subnet Mask:

Gateway:

DNS:

Internet Setup

PPTP

Choose PPTP (Point-to-Point-Tunneling Protocol ) if your ISP uses a PPTP connection. Your ISP will provide you with

a username and password. This option is typically used for DSL services.

Server IP:

PPTP Account:

PPTP Password:

Maximum Idle

Time:

MTU:

Connect Mode:

Page 22 / 78

22

D-Link WBR-2310 User Manual

Section 3 - Conﬁguration

Select

Dynamic

(most common) or

Static

. Select

Static

if your ISP

assigned you the IP address, subnet mask, gateway, and DNS server

addresses.

Enter the IP address (Static L2TP only).

Enter the Primary and Secondary DNS Server Addresses (Static

L2TP only).

Enter the Gateway IP Address provided by your ISP.

The DNS server information will be supplied by your ISP (Internet

Service Provider.)

Enter the Server IP provided by your ISP (optional).

Enter your L2TP account name.

Enter your L2TP password and then retype the password in the next

box.

Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable

Auto-reconnect.

Maximum Transmission Unit - you may need to change the MTU for optimal performance with your speciﬁc ISP. 1492 is the

default MTU.

Select either Always-on, Manual, or Connect-on demand.

L2TP:

IP Address:

Subnet Mask:

Gateway:

DNS:

Server IP:

L2TP Account:

L2TP Password:

Maximum Idle

Time:

MTU:

Connect Mode:

Internet Setup

L2TP

Choose L2TP (Layer 2 Tunneling Protocol) if your ISP uses a L2TP connection. Your ISP will provide you with a username

and password. This option is typically used for DSL services.

Page 23 / 78

23

D-Link WBR-2310 User Manual

Section 3 - Conﬁguration

Enter your Big Pond user name.

Enter your Big Pond password and then retype

the password in the next box.

Enter the IP address of the login server.

The default MAC Address is set to the WAN’s

physical interface MAC address on the

Broadband Router. It is not recommended that

you change the default MAC address unless

required by your ISP.

The default MAC address is set to the WAN’s

physical interface MAC address on the

Broadband Router. You can use the “Clone

MAC Address” button to copy the MAC address

of the Ethernet Card installed by your ISP and

replace the WAN MAC address with the MAC

address of the router. It is not recommended

that you change the default MAC address unless

required by your ISP.

User Name:

Password:

Auth Server:

Login Server IP:

MAC Address:

Clone MAC

Address:

Internet Setup

Big Pond

Page 24 / 78

24

D-Link WBR-2310 User Manual

Section 3 - Conﬁguration

Enter the IP address assigned by your ISP.

Enter the Subnet Mask assigned by your ISP.

Enter the Gateway assigned by your ISP.

The default MAC Address is set to the WAN’s physical

interface MAC address on the Broadband Router. It is not

recommended that you change the default MAC address

unless required by your ISP.

The default MAC address is set to the WAN’s physical

interface MAC address on the Broadband Router. You can

use the

Clone MAC Address

button to copy the MAC

address of the Ethernet Card installed by your ISP and

replace the WAN MAC address with the MAC address

of the router. It is not recommended that you change the

default MAC address unless required by your ISP.

Enter the Primary DNS server IP address assigned by

your ISP.

Enter the Secondary DNS server IP address assigned by your ISP.

Maximum Transmission Unit - you may need to change the MTU for optimal performance with your speciﬁc ISP. 1492 is

the default MTU.

IP Address:

Subnet Mask:

ISP Gateway:

MAC Address:

Clone MAC

Address:

Primary DNS

Address:

Secondary DNS

Address:

MTU:

Internet Setup

Static (assigned by ISP)

Select Static IP Address if all WAN IP information is provided to you by your ISP. You will need to enter in the IP address, subnet mask,

gateway address, and DNS address(es) provided to you by your ISP. Each IP address entered in the ﬁelds must be in the appropriate IP

form, which are four octets separated by a dot (x.x.x.x). The Router will not accept the IP address if it is not in this format.

Page 25 / 78

25

D-Link WBR-2310 User Manual

Section 3 - Conﬁguration

Check the box to enable the wireless function. If you do not want to use

wireless, uncheck the box to disable all the wireless functions.

Service Set Identiﬁer (SSID) is the name of your wireless network. Create

a name using up to 32 characters. The SSID is case-sensitive.

Indicates the channel setting for the WBR-2310. By default the channel

is set to 6. The Channel can be changed to ﬁt the channel setting for

an existing wireless network or to customize the wireless network. The

Auto Channel Scan

setting can be selected to allow the WBR-2310 to

choose the channel with the least amount of interference.

Super G is a group of performance enhancement features that increase

end user application throughput in an 802.11g network. Super G is

backwards compatible to standard 802.11g devices. For top performance,

all wireless devices on the network should be Super G capable. Select

either Disabled, Super G without Turbo, Super G with Dynamic Turbo.

• Disabled - Standard 802.11g support, no enhanced capabilities.

• Super G without Turbo - Capable of Packet Bursting, FastFrames, Compression, but no Turbo mode.

• Super G with Dynamic Turbo - Capable of Packet Bursting, FastFrames, Compression, and Dynamic Turbo.

This setting is backwards compatible with non-Turbo (legacy) devices. Dynamic Turbo mode is only enabled

when all devices on the wireless network are Super G with Dynamic Turbo enabled.

Extended Range Mode helps reduce dead spots by improving the reception algorithm, which allows your wireless clients to

associate with the WBR-2310 at farther distances. Check the box to enable it.

Enable this mode if your network is made up of purely 802.11g devices. If you have both 802.11b and 802.11g wireless

clients, uncheck the box.

Check this option if you would not like the SSID of your wireless network to be broadcasted by the WBR-2310. If this option

is checked, the SSID of the WBR-2310 will not be seen by Site Survey utilities so your wireless clients will have to know the

SSID of your WBR-2310 in order to connect to it.

Enable Wireless:

Wireless Channel:

Super G Mode:

Wireless Settings

Extended Range

Mode:

Wireless Network

Name:

802.11g Only

Mode:

Enable Hidden

Wireless:

Rate

Popular D-Link Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share