Page 41 / 66 Scroll up to view Page 36 - 40
41
D-Link EBR-2310 User Manual
Section 5 - Troubleshooting
You should start at 1472 and work your way down by 10 each time. Once you get a reply, go up by 2 until you get a
fragmented packet. Take that value and add 28 to the value to account for the various TCP/IP headers. For example,
lets say that 1452 was the proper value, the actual MTU size would be 1480, which is the optimum for the network
we’re working with (1452+28=1480).
Once you find your MTU, you can now configure your router with the proper MTU size.
To change the MTU rate on your router follow the steps below:
• Open your browser, enter the IP address of your router (192.168.0.1) and click
OK
.
• Enter your username (admin) and password (blank by default). Click
OK
to enter the web configuration
page for the device.
• Click on the
Home
tab and click the
WAN
button.
• To change the MTU enter the number in the MTU field and click the
Apply
button to save your settings.
• Test your email. If changing the MTU does not resolve the problem, continue changing the MTU in
increments of ten.
Page 42 / 66
42
D-Link EBR-2310 User Manual
Appendix A - Assigning a Static IP Address
Assigning a Static IP Address
(for Windows
®
2000/XP)
Note: Broadband Routers will automatically assign IP Addresses to the computers on the network, using DHCP (Dynamic
Host Configuration Protocol) technology.
If you are using a DHCP-capable Gateway/Router you will not need to assign
Static IP Addresses.
If you are not using a DHCP capable Gateway/Router, or you need to assign a Static IP Address, please follow these
instructions:
• Go to
Start
• Double-click
on
Control Panel
• Double-click
on
Network Connections
Page 43 / 66
43
D-Link EBR-2310 User Manual
Appendix A - Assigning a Static IP Address
• Right-click
on
Local Area Connections.
Double-click Properties
• Highlight
Internet Protocol(TCP/IP)
• Click
Properties
• Select
Use the following IP address
in the
Internet Protocol
(TCP/IP) Properties
window (shown below.)
Page 44 / 66
44
D-Link EBR-2310 User Manual
Appendix A - Assigning a Static IP Address
• Input your
IP address and subnet mask.
(The IP Addresses
on your network must be within the same range. For example,
if one computer has an IP Address of 192.168.0.2, the other
computers should have IP Addresses that are sequential, like
192.168.0.3 and 192.168.0.4. The subnet mask must be the
same for all the computers on the network.)
• Input your
DNS server addresses.
(Note: If you are entering a DNS server, you must enter the IP Address of
the Default Gateway.)
The DNS server information will be provided by your ISP (Internet Service Provider.)
Page 45 / 66
45
D-Link EBR-2310 User Manual
Appendix B - Adding and Sharing Printers in Windows
®
XP
Adding and Sharing Printers in Windows
®
XP
After you have run the
Network Setup Wizard
on all the computers in your network (please see the
Network Setup
Wizard
section at the beginning of
Networking Basics
,) you can use the
Add Printer Wizard
to add or share a printer
on your network.
Whether you want to add a
local printer
(a printer connected directly to one computer,) share an
LPR printer
(a printer
connected to a print server) or share a
network printer
(a printer connected to your network through a Gateway/Router,)
use the
Add Printer Wizard
, you can find the directions below:
First, make sure that you have run the Network Setup Wizard on all of the computers on your network.
We will show you 3 ways to use the
Add Printer Wizard
1.
Adding a local printer
2.
Sharing an network printer
3.
Sharing an LPR printer
Adding a local printer
(A
printer connected directly to a computer)
A printer that is not shared on the network and is connected directly
to one computer is called a
local printer
. If you do not need to share
your printer on a network, follow these directions to add the printer to
one computer.
• Go to
Start> Printers and Faxes

Rate

4 / 5 based on 1 vote.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top