Page 21 / 66 Scroll up to view Page 16 - 20
21
D-Link EBR-2310 User Manual
Section 3 - Configuration
Select
Dynamic
(most common) or
Static
. Select
Static
if your ISP assigned you the IP address, subnet mask,
gateway, and DNS server addresses.
Enter the IP address (Static L2TP only).
Enter the Primary and Secondary DNS Server Addresses
(Static L2TP only).
Enter the Gateway IP Address provided by your ISP.
The DNS server information will be supplied by your ISP
(Internet Service Provider.)
Enter the Server IP provided by your ISP (optional).
Enter your L2TP account name.
Enter your L2TP password and then retype the password
in the next box.
Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable
Auto-reconnect.
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1492 is the
default MTU.
Select either Always-on, Manual, or Connect-on demand.
L2TP:
IP Address:
Subnet Mask:
Gateway:
DNS:
Server IP:
L2TP Account:
L2TP Password:
Maximum Idle
Time:
MTU:
Connect Mode:
Choose L2TP (Layer 2 Tunneling Protocol) if your ISP uses a L2TP connection. Your ISP will provide you with a username
and password. This option is typically used for DSL services.
Internet Setup
L2TP
Page 22 / 66
22
D-Link EBR-2310 User Manual
Section 3 - Configuration
Enter your Big Pond user name.
Enter your Big Pond password and then retype
the password in the next box.
Enter the IP address of the login server.
Enter the IP address of the login server.
The default MAC Address is set to the WAN’s
physical interface MAC address on the
Broadband Router. It is not recommended that
you change the default MAC address unless
required by your ISP.
The default MAC address is set to the WAN’s
physical interface MAC address on the
Broadband Router. You can use the “Clone
MAC Address” button to copy the MAC address
of the Ethernet Card installed by your ISP and
replace the WAN MAC address with the MAC
address of the router. It is not recommended
that you change the default MAC address unless
required by your ISP.
User Name:
Password:
Auth Server:
Login Server IP:
MAC Address:
Clone MAC
Address:
Internet Setup
Big Pond
Page 23 / 66
23
D-Link EBR-2310 User Manual
Section 3 - Configuration
Port Forwarding Rules
This will allow you to open a single port or a range of ports.
Check the box to enabled the rule.
Enter a name for the rule.
Enter the IP address of the computer on your
local network that you want to allow the incoming
service to.
Enter the port or ports that you want to open.
If you want to open 1 port, enter the same port
in both boxes.
Select
TCP
,
UDP
, or
ANY
.
Rule:
Name:
IP Address:
Start Port/
End Port:
Traffic Type:
Page 24 / 66
24
D-Link EBR-2310 User Manual
Section 3 - Configuration
Application Rules
Some applications require multiple connections, such as Internet gaming, video conferencing, Internet telephony and
others. These applications have difficulties working through NAT (Network Address Translation). Special Applications
makes some of these applications work with the WBR-1310.
Check the box to enabled the rule.
Enter a name for the rule.
This is the port used to trigger the application. It
can be either a single port or a range of ports.
This is the port number on the WAN side that
will be used to access the application. You may
define a single port or a range of ports. You
can use a comma to add multiple ports or port
ranges.
Select
TCP
,
UDP
, or
ANY
.
Rule:
Name:
Trigger Port:
Firewall Port:
Traffic Type:
Page 25 / 66
25
D-Link EBR-2310 User Manual
Section 3 - Configuration
Network Filter
Select Disable MAC filters, allow MAC addresses
listed below, or deny MAC addresses listed
below.
Enter the MAC address you would like to filter.
To find the MAC address on a computer, please
refer to the Networking Basics section in this
manual.
Select a DHCP client from the drop-down menu
and click
<<
to copy that MAC Address.
Configure MAC
Filter:
MAC Address:
DHCP Client:
Use MAC (Media Access Control) Filters to allow or deny LAN (Local Area Network) computers by their MAC addresses
from accessing the Network. You can either manually add a MAC address or select the MAC address from the list of
clients that are currently connected to the Broadband Router.

Rate

3.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top