D-Link DWR-953 Router Manual PDF (Setup & Configuration Guide)

Page 31 / 100 Scroll up to view Page 26 - 30

27

D-Link DWR-953 User Manual

Section 3 - Conﬁguration

WEP

Select either a

64Bit

or

128Bit

WEP key length.

Select whether to use

Both

or

Shared Key

authentication.

For a 64-bit key, enter 10 hexadecimal (0-9, A-F) values or 5 ASCII

values. For a 128-bit key, enter 26 hexadecimal values or 13 ASCII

values.

WEP Key Length:

Authentication:

WEP Key:

WPA-Personal

Select

Auto (WPA or WPA2)

,

WPA only

, or

WPA2 only

.

Select

TKIP

,

AES

, or

TKIP and AES

.

AES

is the most secure, but

TKIP

allows for compatibility with clients that don’t support

AES

.

If you are using a Pre-Shared Key (PSK), choose a key (between 8

and 63 characters) here.

WPA Mode:

Cipher Type:

Pre-Shared Key:

Page 32 / 100

28

D-Link DWR-953 User Manual

Section 3 - Conﬁguration

WPS

Enable

or

Disable

Wi-Fi Protected Setup (WPS).

Displays the current PIN. Click

Generate New PIN

if you want to

generate a new one.

Select either

Registrar

or

Enrollee.v

Displays the current WPS conﬁguration status. Click

Release

to

re-conﬁgure.

Check the box to disable the WPS PIN method.

Select either

Push Button

or

PIN Code.

Displays the current WPS status. Click

Trigger

to activate WPS.

WPS:

AP PIN:

Conﬁg Mode:

Conﬁg Status:

Disable WPS-PIN

Method:

Conﬁg Method:

WPS Status:

Page 33 / 100

29

D-Link DWR-953 User Manual

Section 3 - Conﬁguration

Wi-Fi Advanced

Specify a value for the beacon interval. Beacons are packets sent

by an access point to synchronize a wireless network. 100 is the

default and recommended setting.

Set the transmitting power of the antennas.

This value should remain at its default setting of 2347. If you

encounter inconsistent data ﬂow, only minor modiﬁcations are

recommended.

The fragmentation threshold determines whether packets will

be fragmented. Packets exceeding the speciﬁed value will be

fragmented before transmission. 2346 is the default setting.

A Delivery Traﬃc Indication Message (DTIM) is a countdown

informing clients of the next window for listening to broadcast

and multicast messages.

WMM (Wi-Fi Multimedia) is a QoS (Quality of Service) system for

your wireless network. Enable this option to improve the quality of

video and voice applications for your wireless clients.

Select the basic transfer rates based on the speed of wireless

adapters on your wireless network. It is strongly recommended to

keep this setting to

Best

.

Check this box to reduce the guard interval to 400 ns. This can

increase the throughput rate provided that the delay spread of the

connection is also low. However, it can also increase error rate in

some installations, due to increased sensitivity to radio-frequency

reﬂections.

Beacon Interval:

Transmit Power:

RTS Threshold:

Fragmentation:

DTIM Interval:

WMM Capable:

TX Rates:

Short GI:

Page 34 / 100

30

D-Link DWR-953 User Manual

Section 3 - Conﬁguration

Select

Enable

to reduce interference from other wireless networks

in your area. If the channel width is operating at 40 MHz and there

is another wireless network’s channel overlapping and causing

interference, the router will automatically change to 20 MHz.

HT 20/40

Coexistence:

Page 35 / 100

31

D-Link DWR-953 User Manual

Section 3 - Conﬁguration

LAN

Enter the IP address of the router. The default is

192.168.0.1

.

If you change the IP address, you will need to enter the new IP

address in your browser to get into the conﬁguration utility.

Enter the subnet mask of the router. The default subnet mask is

255.255.255.0

.

Enter the local domain name for your network.

IP Address:

Default Subnet

Mask:

Local Domain

Name:

Device List

LAN Settings

The

Device List

displays a list of recognised LAN clients, showing their

Host

Name

,

IP Address

, and

MAC Address

.

Rate

Popular D-Link Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share