Page 46 / 100
Scroll up to view Page 41 - 45
42
D-Link DWR-953 User Manual
Section 3 - Configuration
Inbound Filter
Check this box to enable the filter.
You may select
Always On
or choose the number of a schedule
rule that you have defined. Click
Copy to
to copy the rule to the
specified ID.
Select whether to
Allow
or
Deny
all data to pass except those
matching the rules configured on this page.
Identifies the filter.
Specify the local IP address and then specify the port after the
colon.
Specify the remote IP address and then the port after the colon.
Select this box to enable the filter.
Specify the schedule rule number or click
Add New Rule...
to add
a new schedule rule.
Inbound Filter:
Use schedule
rule:
Inbound Filter
rules list:
ID:
Source IP : Ports:
Destination IP :
Ports:
Enable:
Schedule Rule #:
The
Inbound Filter
enables you to control what packets are allowed to pass through the router. The inbound filter only applies to packets that
are destined for virtual servers or DMZ hosts.
Page 47 / 100
43
D-Link DWR-953 User Manual
Section 3 - Configuration
Select whether the local SNMP administration should be
Enabled
or
Disabled
.
Select whether the local SNMP administration should be
Enabled
or
Disabled
.
Enter the password public in this field to allow read-only access
to network administration using SNMP. You can view the network,
but no configuration is possible with this setting.
Enter the password private in this field to enable read/write access
to the network using SNMP.
Enter up to 4 IP addresses to use as trap targets for your network.
Select the SNMP version of your system.
If you want to limit remote access SNMP access, enter the IP
address of the remote computer you will use to access this device;
all other IP addresses will be denied remote SNMP access.
SNMP Local:
SNMP Remote:
Get Community:
Set Community:
IP 1 ~ 4:
SNMP Version:
WAN Access IP
Address:
SNMP
SNMP (Simple Network Management Protocol) is a widely used network monitoring and control protocol that reports activity on each network
device to the administrator of the network. SNMP can be used to monitor traffic and statistics of the DWR-953. The DWR-953 supports SNMP v1
or v2c.
Page 48 / 100
44
D-Link DWR-953 User Manual
Section 3 - Configuration
Click Enable UPnP to use the Universal Plug and Play (UPnP™)
feature. UPnP provides compatibility with networking equipment,
software and peripherals.
Select the box to allow the WAN port to be “pinged.” Blocking the
Ping option may provide some extra security from hackers.
Enable UPnP:
Enable WAN
Ping Respond:
Advanced Network
Advanced Network contains settings which can change the way the router handles certain types of traffic. We recommend that you do not
change any of these settings unless you are already familiar with them or have been instructed to do so.
Page 49 / 100
45
D-Link DWR-953 User Manual
Section 3 - Configuration
Check the box to enable TR069.
Enter the ACS URL.
Enter your ACS username.
Enter your ACS password.
Enter the connection request port.
Enter the connection request username.
Enter the connection request password.
Select either
Disable
or
Enable
.
Enter the interval time here in seconds.
TR069:
ACS URL:
ACS Username:
ACS Password:
Connection
Request Port:
Connection
Request
Username:
Connection
Request
Password:
Inform:
Interval:
TR069
This page allows you to configure the router’s TR069 settings. TR-069 provides standardized remote device management for residential
gateways, which allows your router to be configured remotely by your ISP (if supported), or any service providing Auto-Configuration Servers
(ACS). If you wish to configure TR069 but lack the required settings, contact your Internet Service Provider (ISP).
Page 50 / 100
46
D-Link DWR-953 User Manual
Section 3 - Configuration
Displays the current time and date of the router.
Select the appropriate time zone from the drop-down box.
Check the box to enable daylight saving time.
Check the box to automatically synchronize the router with an
Internet time server.
Choose the NTP Server used for synchronizing time and date. Click
Update Now
to synchronize with the NTP server now.
Shows the result of the last time synchronization.
Time:
Time Zone:
Enable Daylight
Saving:
Automatically
synchronize
with Internet
time server:
NTP Server
Used:
Sync. Result:
System
This section will help you set the time zone that you are in and the NTP (Network Time Protocol) server. Daylight saving can also be configured to
adjust the time when needed.
Time Settings
19216811.live