Page 11 / 58
Scroll up to view Page 6 - 10
11
You will need broadband Internet access (a Cable or DSL-subscriber line into
your home or office).
Consult with your Cable or DSL provider for proper installation of the modem.
Connect the Cable or DSL modem to the DI-604 Router. (
See the printed Quick
Installation Guide included with your router.
)
If you are connecting a desktop computer to your network, install the D-Link
DWL-G520 wireless PCI adapter into an available PCI slot on your desktop
computer.
(See the printed Quick Installation Guide included with the network adapter.)
Install the drivers for the D-Link DWL-G650 wireless Cardbus adapter into a
laptop computer.
(
See the printed Quick Installation Guide included with the DWL-G650.
)
Getting Started (continued)
For a typical wireless setup at home (as shown above), you may do the
following:
Setting up
an example
of a Wireless
Infrastructure
Network
2
3
4
Connect the DWL-2200AP to the PoE base unit. (
See the printed Quick
Installation Guide included with the DWL-2200AP.
)
1
6
Access Point Mode
5
Connect the Ethernet Broadband Router to the PoE base unit. (
See the printed
Quick Installation Guide included with the DWL-2200AP.
)
7
Downloaded from
www.Manualslib.com
manuals search engine
Page 12 / 58
12
Getting Started (continued)
Connecting
PoE
(Power over Ethernet)
Connect one end of an Ethernet cable (included with your package) to the
LAN port
on the DWL-2200AP and the other end of the Ethernet cable to
the port labeled
P+DATA OUT
on the PoE base unit.
Connect another Ethernet cable from the
DATA IN
port on the PoE base unit
to your router/switch or to a PC.
Attach the power adapter to the connector labeled
POWER IN
on the PoE
base unit. Attach the power cord to the power adapter and into an electrical
outlet.
Step 1
Step 2
Step 3
Downloaded from
www.Manualslib.com
manuals search engine
Page 13 / 58
13
Note: if you have changed the default IP address assigned to the DWL-2200AP, make sure
to enter the correct IP address.
Using the Configuration Menu
After you have completed the
Setup Wizard
(please see the
Quick Installation Guide
that
came with the product) you can access the
Configuration
menu at any time by opening
the Web browser and typing in the IP address of the DWL-2200AP. The DWL-2200AP
default IP address is shown below:
±
Open the Web browser
±
Type in the
IP address
of the
DWL-2200AP
±
Home > Wizard
The
Home>Wizard
screen will appear.
Please refer to the
Quick
Installation Guide
for more
information regarding the
Setup Wizard.
±
±
Type
admin
in the
User Name
field
Leave the
Password
blank.
(However, if you have changed
the password, please enter the
correct password.)
Click
OK
admin
DWL-2200AP
It is recommended that you use an Ethernet connection to configure the DWL-2200AP.
Downloaded from
www.Manualslib.com
manuals search engine
Page 14 / 58
14
Using the Configuration Menu (continued)
Home > Wireless
Channel-
6
is the default channel. All devices on the network must share the same
channel.
Wireless
Band-
802.11g.
SSID-
Service Set Identifier (SSID) is the name designated for a specific wireless
local area network (WLAN). The SSID’s factory default setting is
default.
The SSID can be easily changed to connect to an existing
wireless network or to establish a new wireless network.
SSID
Broadcast-
Enable or Disable SSID Broadcast. Enabling this feature broadcasts the
SSID across the network.
Radio
Frequency-
The radio frequency will remain at 2.437GHz .
Apply-
Click
Apply
to save the changes.
Downloaded from
www.Manualslib.com
manuals search engine
Page 15 / 58
15
Using the Configuration Menu (continued)
Home > LAN
LAN is short for Local Area Network. This is considered your internal network. These are
the IP settings of the LAN interface for the DWL-2200AP. These settings may be referred
to as private settings. You may change the LAN IP address if needed. The LAN IP
address is private to your internal network and cannot be seen on the Internet.
Click
Apply
to save the changes.
Get IP From-
Select
Static (Manual)
or
Dynamic (DHCP)
as the method you
will use to assign an IP address to the DWL-2200AP.
Apply-
Default Gateway-
This field is optional. Enter in the lP address of the router on your
network.
Subnet Mask-
The subnet mask of the LAN interface.
The default subnet mask is
255.255.255.0
IP Address-
The IP address of the LAN interface.
The default IP address is:
192.168.0.50
Downloaded from
www.Manualslib.com
manuals search engine
19216811.live