Page 6 / 30
Scroll up to view Page 1 - 5
DVG-5102S
User’s Manual
Telephone Interface Description
D-Link Systems, Inc.
6
Rear Panel
1.
Phone Port:
Connect to your phones using standard phone cabling (RJ-11).
2.
WAN:
Connect to your broadband modem / router using an Ethernet cable.
3.
LAN:
Connect to your Ethernet enabled computers using Ethernet cabling.
4.
Power Receptor:
Receptor for the provided power adapter.
5.
Reset :
Use to Restore to factory default :
(1)
Power on.
(2)
Press and hold the reset button for 5 seconds.
(3)
Release the reset button. Factory settings will be restored.
WARNING:
DO NOT
connect any phone port directly to a PSTN line (FXS to PSTN) or to an
internal PBX line (FXS to PBX extension). Doing so may damage your VoIP TA.
Page 7 / 30
DVG-5102S
User’s Manual
MAINTENANCE
D-Link Systems, Inc.
7
2. Getting Started
To access the web-based configuration utility,
set a statics IP on the LAN adapter,
open a web browser such
as Internet Explorer and enter the IP address of the DVG-5102S.
*Statics IP: 192.168.8
.XXX, the “XXX”
can be any number from 1~253 except 254 cannot be used*
If the DVG-
5102S is connected behind a router, the IP address of the router is determine by the router’s
DHCP Server.
Open your Web browser and type
into the URL address
box. Press the Enter or Return Key.
Click
Login
to enter Web Site.
Page 8 / 30
DVG-5102S
User’s Manual
MAINTENANCE
D-Link Systems, Inc.
8
VoIP TA Web Configuration
During configuration, please follow the Setup Hint for some specific procedure in case the VoIP TA fails
to make the changes active.
Situation 1:
(example: Internet Setup)
Setup Hint:
1.
Select DHCP WAN Setup.
2.
Click
“
Apply
”
.
3.
Click
“
Save and Restart
”
to make change take effect.
Page 9 / 30
DVG-5102S
User’s Manual
MAINTENANCE
D-Link Systems, Inc.
9
Situation 2:
(example: Enable IP Filtering)
Setup Hint:
1.
Click
“
Enable IP Filtering
”
check box to open the main screen.
2.
Click
“
Add
”
to enter an entry.
3.
After Adding an entry, you have to click
“
Apply
”
.
4.
Don
’
t forget to click
“
Apply
”
which in the field of
“
Enable IP Filtering
”
.
5.
After settings, save and reboot.
1
2
3
4
Page 10 / 30
DVG-5102S
User’s Manual
MAINTENANCE
D-Link Systems, Inc.
10
2-1 SETUP
2-1-1 Internet Setup
WAN (Wide Area Network) Settings are used to connect to your ISP (Internet Service Provider). The
WAN settings are provided to you by your ISP and oftentimes referred to as "public settings". Please
select the appropriate option for your specific ISP.
IP Configuration (Setting WAN Port)
There are five methods of obtaining a WAN port IP address:
1.
DHCP, which means a Dynamic IP (Cable Modem)
2.
Static IP
3.
PPPoE (dial-up ADSL)
Methods for using DHCP and PPPoE for obtaining an IP address may vary. If you are not familiar with
creating a network connection, please contact your local ISP.
After selecting the suitable option, click
Accept
at the bottom of the screen to save the settings.
You need to save the changes and restart the VoIP TA to make the changes active. Saving the settings:
Click
MAINTENANCE
and select
Save/Restart
in
System
from the left menu. Tick
Save Settings
and
Restart
, then click
Accept
. Wait for about 40 seconds before the VoIP TA obtaining an IP address by
the method you selected.
Note:
When the system has obtained a new IP address, and you are using a WAN port to enter the
Web Configuration Screen, the new IP address has to be used before you can get connected to the
VoIP TA. The same principle applies to the next two settings.
SETUP
→
Internet Setup
SETUP
→
Internet Setup
19216811.live