32

D-Link DSL-2770L User Manual

Section 3 - Configuration

3G

These settings allow you to configure the router to share a mobile Internet connection from a connected 3G USB adapter.

Select whether to try and auto-detect your 3G settings, or to manually

set them up. You can click the Auto-Detection button to try and auto-

detect your current settings.

If you selected

Manual

for

Dial-Up.Profile

, you can enter your

Country

,

Telecom

, and

3G.Network.

to automatically fill in some of the settings

for you.

Select whether to use

3G.Only.Mode

,

2G.Only.Mode

, or use

Auto.

Mode

to automatically switch between the two.

Enter the username for your account (optional).

Enter the password for your account (optional).

Enter the dial number as given to you by your Internet Service Provider.

If you selected

Manual

for

Dial-Up. Profile

, you can set your

authentication to

Auto

,

PAP

, or

CHAP

authentication.

If you selected

Manual

for

Dial-Up.Profile

, enter your APN here.

If you selected

Manual

for

Dial-Up.Profile

, enter your PIN code here.

Enter the Primary and secondary DNS server IP addresses assigned by

your ISP. These addresses are usually obtained automatically from your

ISP. Leave at 0.0.0.0 if you did not specifically receive these from your ISP.

You can select whether you want to use a keep alive method to keep

your connection active.

Dial-Up Profile:

Country/

Telecom/3G

Network:

Prefer Service Type:

Username:

Password:

Dialed Number:

Authentication:

APN:

PIN Code:

Primary/Secondary

DNS Server:

Keep Alive:

33

D-Link DSL-2770L User Manual

Section 3 - Configuration

If you select

Use.Ping

, enter the ping interval and address to ping.

If you select

Use.LCP.Echo.Request

, enter the

lcp.echo.interval

and

lcp.failure

limit.

Checking this box will enable ping testing, and you can set the ping

interval, address, and packet size using the corresponding text boxes.

Check this box if you want the router to use NAT to provide IP addresses

for your computers and devices. If this is disabled, your devices will need

to get IP addresses from your ISP or configured individually.

You can select your country and Internet Service Provider to

automatically fill in the necessary

Multicast

and

IGMP.Snooping

settings.

Ping Test:

Enable NAT:

Country/ISP

Provider:

34

D-Link DSL-2770L User Manual

Section 3 - Configuration

Wireless Settings

If you want to configure the wireless settings on your router using a guided

wizard, click

Wireless.Connection.Setup.Wizard

.

Click

Wi-Fi.Protected.Setup

if you want to add a wireless device using

Wi-Fi Protected Setup (WPS).

If you want to manually configure the wireless settings on your router, click

Manual

Wireless.Connection.Setup.

and refer to the next page.

35

D-Link DSL-2770L User Manual

Section 3 - Configuration

The Wireless Connection Setup Wizard is designed to guide you through

a step-by-step process to configure your wireless network.

Type your desired wireless network name (SSID), then click

Next

.

Wireless Connection Setup Wizard

Choose what level of wireless security you want to use. It is highly

recommended that you select

BEST

. Click

Next

to continue.

Based on the level of wireless security you chose, you will need to enter a

password for your wireless network. Click

Next

to continue.

Wireless setup is now complete. Click

Save.

to save your settings and

complete the setup process.

36

D-Link DSL-2770L User Manual

Section 3 - Configuration

Wi-Fi Protected Setup

If you clicked on the Wi-Fi Protected Setup button on the Wireless Setup page, you

will see this screen. The Wi-Fi Protected Setup page allows you to create a wireless

connection between your router and a device automatically by simply pushing a button

or entering a PIN code.

You can also use Windows 7 to do initial configuration of your router by using the

Connect to a network

wizard in Windows, and entering the WPS PIN/AP PIN of the

router when prompted. After modifying any settings, click

Save Settings

to save your

changes.

Select whether you would like to enable or disable WPS features.

If you use Windows 7’s

Connect to a network

wizard to do initial

configuration of the router, you will need to enter the WPS PIN/AP PIN

into the wizard when prompted. The factory default WPS PIN/AP PIN is

printed on a label located on the bottom of the router. You can click the

Generate New PIN

button to change it to a randomly generated PIN.

Select whether the WPS config mode should be set to

Registrar

or

Enrollee

. In most cases, this should be set to

Registrar

so that you can

use WPS to connect new wireless clients.

If this is set to

CONFIGURED

, the router will be marked as “already

configured” to computers that try to use WPS configuration, such as

Windows 7’s

Connect to a network

wizard. You can click the

Release

button to change the status to

UNCONFIGURED

to allow for WPS

configuration of the router.

If this is set to

UNCONFIGURED

, you can click the

Set

button to change

the status to

CONFIGURED

to block WPS configuration of the router.

This lets you choose whether to use the

Push Button

connection

method (PBC) or

PIN

method to connect to a wireless client when the

Trigger

button is clicked. If you choose the

PIN

method, you will need

to enter an 8-digit PIN number that the wireless client need to use to

connect to your router.

This will show the current WPS connection process status. Click the

Trigger

button to initiate a WPS connection.

WPS:

AP PIN (also known

as WPS PIN):

Config Mode:

Config Status:

Config Method:

WPS Status: