Page 26 / 122 Scroll up to view Page 21 - 25
22
D-Link DSL-2770L User Manual
Section 3 - Configuration
IP over ATM(RFC 1483 Routed)
Select
Static.IP
if your ISP assigned you an IP address, subnet mask,
gateway, and DNS server address. In most cases, select
Dynamic.IP
.
Enter the Primary and secondary DNS server IP addresses assigned by
your ISP.
If your ISP requires you to enter a MAC address, fill it in here. You can click
the Clone MAC button to enter your current computer’s MAC address.
If you experience connection issues, you may need to change the
MTU setting for optimal performance with your specific ISP. 1500 is
the default MTU.
Check this to enable the router to use NAT to assign IP addresses for
your devices.
Address Mode
Primary/Secondary
DNS Server:
MAC Address:
MTU:
Enable NAT:
Page 27 / 122
23
D-Link DSL-2770L User Manual
Section 3 - Configuration
PPP over Ethernet
Check this box to enable IPv6/IPv4 dualstack.
Enter the username for your ADSL account.
Enter the password for your ADSL account, then type it again in the
Verify Password box.
You can enter a name for your service here.
Enter the IP address assigned to you by your ISP.
Enter the Primary and secondary DNS server IP addresses assigned by
your ISP.
If your ISP requires you to enter a MAC address, fill it in here. You can click
the Clone MAC button to enter your current computer’s MAC address.
If you experience connection issues, you may need to change the
MTU setting for optimal performance with your specific ISP. 1500 is
the default MTU.
Check this to enable the router to use NAT to assign IP addresses for
your devices.
IPv6 Dualstack:
Username:
Password/Verify
Password:
Service Name:
IP Address:
Primary/Secondary
DNS Server:
MAC Address:
MTU:
Enable NAT:
Page 28 / 122
24
D-Link DSL-2770L User Manual
Section 3 - Configuration
Check this box to enable IPv6/IPv4 dualstack.
Enter the username for your ADSL account.
Enter the password for your ADSL account, then type it again in the
Verify PPPoA Password box.
You can enter a name for your service here.
Enter the IP address assigned to you by your ISP.
Enter the Primary and secondary DNS server IP addresses assigned by
your ISP.
If you experience connection issues, you may need to change the
MTU setting for optimal performance with your specific ISP. 1500 is
the default MTU.
Check this to enable the router to use NAT to assign IP addresses for
your devices.
Dualstack:
PPPoA Account:
PPPoA Password/
Verify PPPoA
Password:
Service Name:
IP Address:
Primary/Secondary
DNS Server:
MTU:
Enable NAT:
PPP over ATM
Page 29 / 122
25
D-Link DSL-2770L User Manual
Section 3 - Configuration
There are no extra settings to configure when you choose this option.
See the ADSL Interface page to configure the settings below.
RFC1483 Bridged
Page 30 / 122
26
D-Link DSL-2770L User Manual
Section 3 - Configuration
Ethernet/3G WAN Interface
If you clicked the Setup button for Ethernet/3G WAN Interface, you will see the following settings. You can click the
Setup.Wizard.
button to use
a step-by-step wizard that guides you through configuration of your WAN settings. If you are not sure what settings to use, please contact your
Internet Service Provider.
Select the WAN interface to configure, and whether to enable or disable
it.
Select Static IP, DHCP, PPoE, PPTP, L2TP, or 3G(through a USB adapter).
Based on the setting you choose, the following settings will be different.
Enter a host name to use for your connection.
WAN Interface:
My Internet
Connection Is:
Host Name:
The settings displayed in the middle will vary depending on what you select for the
My.
Internet.Connection.Is
setting. See the following pages for details.
Select what multicast mode to use (Auto/IGMP v1/IGMP v2/IGMP v3),
or if you want to disable it.
Check this box if you want to enable IGMP Snooping.
To set a VLAN tag, check this box, then enter the VLAN TAG to use.
Multicast:
IGMP Snooping:
VLAN TAG:

Rate

3.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top