Page 21 / 97 Scroll up to view Page 16 - 20
21
D-Link DSL-2740B ADSL2+ Modem with Wireless N 300 Router
Section 6 - Setup
LAN Settings
In this section, you can configure the DSL Router IP Address and Subnet Mask for the LAN interface.
Apply Settings
The Setup is now complete. Click Finish to apply the current settings.
Page 22 / 97
22
D-Link DSL-2740B ADSL2+ Modem with Wireless N 300 Router
Section 6 - Setup
Internet Setup
Internet Setup is an advanced version of the Setup Wizard.
If you want to manually configure your DSL connection, consider going through this
advanced setup for a more comprehensive configuration. Configure the DSL settings as provided by your ISP.
Click on the
Add
button if you want to add a new connection for the Wide Area Network (WAN) interface and to proceed to the ATM PVC Configuration
screen.
The ATM PVC Configuration screen allows you to configure your Internet connection.
Find your account settings from your ISP before you proceed.
Page 23 / 97
23
D-Link DSL-2740B ADSL2+ Modem with Wireless N 300 Router
Section 6 - Setup
ATM PVC Configuration
These values are required for all DSL connection types
and are provided by your ISP.
Use the default setting unless otherwise instructed by
your ISP.
Use the default setting unless otherwise instructed
by your ISP.
For more information about QoS, see the
Quality of Service section in this user manual.
VPI/VCI:
Service
Category:
Enable QoS:
Page 24 / 97
24
D-Link DSL-2740B ADSL2+ Modem with Wireless N 300 Router
Section 6 - Setup
Connection Type
This field shows the types of network protocols and encapsulation modes that can be configured.
Connection Type:
Select the connection type that your ISP has instructed to use.
• PPP over ATM (PPPoA)
• PPP over Ethernet (PPPoE)
• MAC Encapsulation Routing (MER)/DHCP
• IP over ATM (IPoA)
• Bridging
PPPoE, MER (also referred to as DHCP) and Bridging are the most common
connection types in North America.
To set up a PPPoE, MER or Bridging
connection, follow the instructions on the following pages of this user
manual.
PPPoA and IPoA are more widely utilized in other regions.
Setup
for PPPoA and IPoA are similar to PPPoE and MER, respectively.
Encapsulation Mode:
Use the default setting unless otherwise instructed by your ISP.
Note:
These settings are ISP dependant.
For information regarding proper configuration, contact your ISP.
Page 25 / 97
25
D-Link DSL-2740B ADSL2+ Modem with Wireless N 300 Router
Section 6 - Setup
PPP over Ethernet (PPPoE)
Enter your username as provided by your ISP.
Enter your password as provided by your ISP.
Enter any name that will help you identify your connection.
This
field will not affect your connection.
Use the default setting unless otherwise instructed by your ISP.
Use the default setting of 1492 unless otherwise instructed by
your ISP.
Use the default setting unless otherwise instructed by your ISP.
Select if you would like to share your internet connection with
multiple computers.
The router will share your DSL connection
with wired and wirelessly connected computers.
Select this option if you would like to utilize a one-to-one Network
Address Translation.
It will map a single internal IP address to a
single external IP address.
Select if you would like to utilize the firewall to help protect you
from unwanted internet threats
PPP Username:
PPP Password:
PPPoE Service Name:
Authentication
Method:
MTU:
MRU:
Enable NAT:
Enable Fullcone NAT:
Enable Firewall:

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top