Page 66 / 91
Scroll up to view Page 61 - 65
Web Configuration
D-Link DSL-2640B User Manual
62
Click
Add
and the page as shown in the figure appears.
The table describes the parameters in this page.
Field
Description
Traffic Class Name
Enter the name of the traffic class.
Assign Classification
Queue
Specify the queue to which the packet belongs. You can
set the queue in the classification configuration.
DSCP Mark
Attach the DSCP mark to the mapped packet.
Physical LAN Port
Select the physical port of the packet from the drop-down
list.
Source MAC Address
Enter the source MAC address of the packet.
Source MAC Mask
Use mask 000000ffffff to mask the MAC address. 00
indicates not mapped and ff indicates mapped.
Destination
MAC
Address
Enter the destination MAC address of the packet.
Destination
MAC
Mask
Use mask 000000ffffff to mask the MAC address. 00
indicates not mapped and ff indicates mapped
802.1p Priority
Select the 802.1p priority of the packet from the
drop-down list. You can select
Any
or a value in the range
of 0—7. Note that this function is not supported at the
moment.
Click
Apply
to save the settings.
Page 67 / 91
Web Configuration
D-Link DSL-2640B User Manual
63
UPnP
Choose
ADVANCED
>
Network Tools
and click
UPnP
. The page shown in the following
figure appears.
In this page, you can configure universal plug and play (UPnP). The system acts as a
daemon after you enable UPnP.
UPnP is used for popular audio visual software. It allows automatic discovery of your
device in the network. If you are concerned about UPnP security, you can disable it.
Block ICMP ping should be enabled so that the device does not respond to malicious
Internet requests.
Click
Apply
to save the settings.
ADSL Settings
In the
NETWORK TOOLS
page, click
ADSL
. The page as shown in the figure appears.
In this page, you can select the ADSL modulation. Normally, you are recommended to
keep the factory defaults. The device negotiates the modulation mode with the DSLAM.
Click
Apply
to save the settings.
Page 68 / 91
Web Configuration
D-Link DSL-2640B User Manual
64
SNMP
Choose
ADVANCED
>
Network Tools
and click
SNMP
. The page shown in the right
figure appears.
In this page, you can set SNMP parameters.
°
Read Community
: The network administrator must use this password to read the
information of this device.
°
Set Community
: The network administrator must use this password to configure the
information of this device.
°
Trap Manager IP
: The trap information is sent to this host.
Click
Apply
to save the settings.
Page 69 / 91
Web Configuration
D-Link DSL-2640B User Manual
65
TR-069
In the
NETWORK TOOLS
page, click
TR-069
. The page as shown in the figure appears.
In this page, you can configure the TR-069 CPE. The table describes the parameters in
this page.
Field
Description
Inform
You can select
Disabled
or
Enabled
to disable or enable
notification.
°
Disabled
indicates
that
the
device
does
not
automatically send requests to the TR069 server.
°
Enabled
indicates that the device automatically sends
a request of connection to the TR069 server. The
following function items are available only when
Inform
is set to
Enabled
.
Inform Interval
The interval of sending a request of connection to the
TR069 server from the device.
ACS URL
The path of the TR069 server to which the device sends a
request.
ACS User Name
The user name that the devices uses to log in to the
TR069 server.
ACS Password
The password that the devices uses to log in to the
TR069 server.
Connection Request
Authentication
Select the check box to enable authentication of
connection request. If you enable the function, you need
to enter the user name and password for authentication.
Connection Request
User Name
The user name that the TR069 server uses to access the
TR069 progress of the device.
Connection Request
Password
The password that the TR069 server uses to access the
TR069 progress of the device.
Click
Apply
to save settings.
Page 70 / 91
Web Configuration
D-Link DSL-2640B User Manual
66
Certificates
Choose
ADVANCED
>
Network Tools
and click
Certificates
. The
Certificates
page
shown in the right figure appears.
In this page, you can set local certificate and trusted certificate.
Routing
Choose
ADVANCED
>
Routing
. The page as shown in the figure appears.
19216811.live