1. Home
    2. /
  2. Manuals
    3. /
  3. D-Link
    4. /
  4. DIR-815
    5. /
  5. 8
Page 36 / 136 Scroll up to view Page 31 - 35
31
D-Link DIR-815 User Manual
Section 3 - Configuration
Select Static IP if your ISP assigned you the IP address,
subnet mask, gateway, and DNS server addresses. In most
cases, select Dynamic.
Enter the IP address (Static PPPoE only).
Enter your PPPoE user name.
Enter your PPPoE password and then retype the password
in the next box.
Enter the ISP Service Name (optional).
Use the radio buttons to specify the reconnect mode.
The
user can specify a custom schedule or specify the
On
Demand
, or
Manual
option.
To specify a custom schedule, use the drop-down menu to
select one of the schedules that has been defined in the
Tools
>
Schedules
window. To create a new schedule, click
the
New Schedule
button to open the
Tools> Schedules
window. Refer to “Schedules” on page 83 for more information.
Enter a maximum idle time during which the Internet
connection is maintained during inactivity. To disable this
feature, enable Auto-reconnect.
Enter the Primary and Secondary DNS Server Addresses (Static PPPoE only).
Address Mode:
IP Address:
User Name:
Password:
Service Name:
Reconnect
Mode:
Maximum Idle
Time:
DNS Servers:
Manual Internet Connection Setup
PPPoE (Username/Password)
Select
PPPoE (Username/Password)
from the drop-down menu if your ISP uses a PPPoE connection. Your ISP will provide you
with a username and password. This option is typically used for DSL services. Make sure to remove your PPPoE software from
your computer. The software is no longer needed and will not work through a router.
Page 37 / 136
32
D-Link DIR-815 User Manual
Section 3 - Configuration
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1454 is the default
MTU.
The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended
that you change the default MAC address unless required by your ISP.
You can use the Clone Your PC’s MAC Address button to
replace the Internet port’s MAC address with the MAC address of your Ethernet card.
MTU:
MAC Address:
Click the
Save Settings
button to save any changes made.
Page 38 / 136
33
D-Link DIR-815 User Manual
Section 3 - Configuration
Select
Static IP
if your ISP assigned you the IP address,
subnet mask, gateway, and DNS server addresses. In most
cases, select
Dynamic IP
.
Enter the IP address (Static PPTP only).
Enter the Primary and Secondary DNS Server Addresses
(Static PPTP only).
Enter the Gateway IP Address provided by your ISP.
Enter the Server IP provided by your ISP (optional).
Enter your PPTP username.
Enter your PPTP password and then retype the password
in the next box.
Use the radio buttons to specify the reconnect mode.
The
user can specify a custom schedule or specify the
On
Demand
, or
Manual
option.
To specify a custom schedule, use the drop-down menu to
select one of the schedules that has been defined in the
Tools
>
Schedules
window. To create a new schedule, click
the
New Schedule
button to open the
Tools> Schedules
window. Refer to “Schedules” on page 82 for more information.
Address Mode:
PPTP IP Address:
PPTP Subnet
Mask:
PPTP Gateway IP
Address:
PPTP Server IP
Address:
Manual Internet Connection Setup
PPTP
Username:
Password:
Reconnect
Mode:
Select
PPTP (Point-to-Point Tunneling Protocol)
from the drop-down menu if your ISP uses a PPTP connection. Your ISP will
provide you with a username and password. This option is typically used for DSL services.
Page 39 / 136
34
D-Link DIR-815 User Manual
Section 3 - Configuration
Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable
Auto-reconnect.
The DNS server information will be supplied by your ISP (Internet Service Provider).
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1454 is the default
MTU.
The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended
that you change the default MAC address unless required by your ISP.
You can use the
Clone Your PC’s MAC Address
button to
replace the Internet port’s MAC address with the MAC address of your Ethernet card.
Maximum Idle
Time:
DNS Servers:
MTU:
MAC Address:
Click the
Save Settings
button to save any changes made.
Page 40 / 136
35
D-Link DIR-815 User Manual
Section 3 - Configuration
Select Static if your ISP assigned you the IP address, subnet
mask, gateway, and DNS server addresses. In most cases, select
Dynamic.
Enter the L2TP IP address supplied by your ISP (Static only).
Enter the Subnet Mask supplied by your ISP (Static only).
Enter the Gateway IP Address provided by your ISP.
Enter the Server IP provided by your ISP (optional).
Enter your L2TP username.
Enter your L2TP password and then retype the password in
the next box.
Use the radio buttons to specify the reconnect mode. The
user
can specify a custom schedule or specify the
On Demand
, or
Manual
option.
To specify a custom schedule, use the drop-down menu to
select one of the schedules that has been defined in the
Tools
>
Schedules
window. To create a new schedule, click the
New
Schedule
button to open the
Tools> Schedules
window. Refer
to “Schedules” on page 83 for more information.
Address Mode:
L2TP IP Address:
L2TP Subnet
Mask:
Manual Internet Connection Setup
L2TP
Choose
L2TP
(Layer 2 Tunneling Protocol) if your ISP uses a L2TP connection. Your ISP will provide you with a username and
password. This option is typically used for DSL services.
L2TP Gateway IP
Address:
L2TP Server IP
Address:
Username:
Password:
Reconnect
Mode:

Rate

124.8 / 5 based on 304 votes.

Popular D-Link Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top