Page 51 / 139 Scroll up to view Page 46 - 50
47
D-Link DIR-636L User Manual
Section 4 - Security
It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish
wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the
added overhead.
1. Log into the web-based configuration by opening a web browser and
entering the IP address of the router (192.168.0.1). Click on
.Setup.
and then click
.Wireless.Settings
on the left side.
2. Next to
Security Mode
, select
WPA-Enterprise
.
3. Next to
WPA Mode
, select
Auto
,
WPA2.Only
, or
.WPA.Only
. Use
Auto
if you have wireless clients using both WPA and WPA2.
4. Next to
Cypher Type
, select
TKIP.and.AES
,
TKIP
, or
AES
.
5. Next to
Group Key Update Interval
, enter the amount of time before
the group key used for broadcast and multicast data is changed
(3600 is default).
6. Next to
Authentication Timeout
, enter the amount of time before a
client is required to re-authenticate (60 minutes is default).
7. Next to
RADIUS Server IP Address
enter the IP Address of your RADIUS
server.
Configure WPA/WPA2-Enterprise (RADIUS)
Page 52 / 139
48
D-Link DIR-636L User Manual
Section 4 - Security
8.
Next to
RADIUS Server Port
, enter the port you are using with
your RADIUS server. 1812 is the default port.
9.
Next to
RADIUS Server Shared Secret
, enter the security key.
10. If the
MAC Address Authentication
box is selected then the user
will need to connect from the same computer whenever logging
into the wireless network.
11. Click
Advanced
to enter settings for a secondary RADIUS Server.
12. Click
Apply.Settings
to save your settings.
Page 53 / 139
49
D-Link DIR-636L User Manual
Section 3 - Configuration
This section will allow you to change the local network settings of the router and to configure the DHCP settings.
Network Settings
Enter the IP address of the router. The default IP address
If you change the IP address, once you click
Save.Settings
,
you will need to enter the new IP address in your browser
to get back into the configuration utility.
Enter the Subnet Mask. The default subnet mask is
255.255.255.0.
Enter a name for the router.
Enter the Domain name (Optional).
Uncheck the box to transfer the DNS server information
from your ISP to your computers. If checked, your
computers will use the router for a DNS server.
Router IP Address:
Subnet Mask:
Device Name:
Local Domain:
Enable DNS Relay:
Router Settings
Page 54 / 139
50
D-Link DIR-636L User Manual
Section 3 - Configuration
DHCP Server Settings
DHCP stands for Dynamic Host Control Protocol. The DIR-636L has a built-in DHCP server. The DHCP Server will automatically
assign an IP address to the computers on the LAN/private network. Be sure to set your computers to be DHCP clients by setting
their TCP/IP settings to “Obtain an IP Address Automatically.” When you turn your computers on, they will automatically load
the proper TCP/IP settings provided by the DIR-636L. The DHCP Server will automatically allocate an unused IP address from
the IP address pool to the requesting computer. You must specify the starting and ending address of the IP address pool.
Check this box to enable the DHCP server on your router.
Uncheck to disable this function.
Enter the starting and ending IP addresses for the DHCP server’s
IP assignment.
Note:
If you statically (manually) assign IP addresses to your
computers or devices, make sure the IP addresses are outside of
this range or you may have an IP conflict.
The length of time for the IP address lease. Enter the Lease time
in minutes.
Enable this feature to broadcast your networks DHCP server to
LAN/WLAN clients.
NetBIOS allows LAN hosts to discover all other computers within
the network, enable this feature to allow the DHCP Server to
offer NetBIOS configuration settings.
Enable this feature to allow WINS information to be learned from the WAN side, disable to allow manual configuration.
This feature allows the configuration of a NetBIOS ‘domain’ name under which network hosts operates. This setting has no effect if
the ‘Learn NetBIOS information from WAN’ is activated.
Enable DHCP
Server:
DHCP IP Address
Range:
DHCP Lease Time:
Always
Broadcast:
NetBIOS
Announcement:
Learn NetBIOS
from WAN:
NetBIOS Scope:
Page 55 / 139
51
D-Link DIR-636L User Manual
Section 3 - Configuration
NetBIOS Node:
WINS IP
Address:
Select the different type of NetBIOS node;
Broadcast.only
,
Point-to-Point
,
Mixed-mode
, and
Hybrid
.
Enter your WINS Server IP address(es).

Rate

3.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top