Page 36 / 197
Scroll up to view Page 31 - 35
DIR-632
Multifunction Wireless Router Supporting WiMAX,
3G GSM/CDMA with Built-in 8-port Switch
User Manual
Installation and Connection
Saving and Restoring Settings
!
Note that you should regularly save the changes of the router's settings to the non-
volatile memory.
The router's web-based interface displays the notification on unsaved changes at the top of the page.
Figure 22. The notification on unsaved changes.
Place the mouse pointer on the
Notifications
icon (
) to view the list of unsaved changes and
click the relevant link.
You can save the router's settings via the top-page menu displayed when the mouse pointer is over
the
System
caption.
Figure 23. The top-page menu.
Click the
Reboot
line if you have already saved the router's settings.
Click the
Save&Reboot
line to save new settings and immediately reboot the router.
Click the
Save
line to save new settings to the non-volatile memory and continue configuring the
device. Also you can save the device's parameters via the
Save
button on the
System /
Configuration
page.
Click the
Backup
line and follow the dialog box appeared to save the configuration (all settings of
the router) to your PC. Also you can save the router's configuration to your PC via the
Backup
button on the
System / Configuration
page.
Click the
Factory
line to restore the factory default settings. Also you can restore the factory
defaults via the
Factory
button on the
System / Configuration
page.
Also you can restore the factory default settings via the hardware
RESET
button. The button is
located on the back panel of the router next to the power connector.
Page
36
of 197
Page 37 / 197
DIR-632
Multifunction Wireless Router Supporting WiMAX,
3G GSM/CDMA with Built-in 8-port Switch
User Manual
Installation and Connection
To restore the factory default settings, insert a small paperclip into the hole of the button (with the
router
powered on
), push, and hold for 10 seconds. Then remove the paperclip. All LEDs of the
router should turn off and then turn on again.
Wait for about 30 seconds. Now you can access the web-based interface of the router using the
default IP address, username and password.
If you fail to restore the factory defaults via the method described above, use the emergency reset
method.
1.
Power off the device.
2.
Insert a small paperclip into the hole of the
RESET
button and push.
3.
Power on the device keeping the button pushed.
4.
After 5 seconds, release the button.
!
When you keep the button pushed for more than 8 seconds, the router switches to crash
recovery mode. To restore normal operation of the router, please, contact the Technical
Support Service.
When you have configured all needed settings, click the
Logout
line.
Page
37
of 197
Page 38 / 197
DIR-632
Multifunction Wireless Router Supporting WiMAX,
3G GSM/CDMA with Built-in 8-port Switch
User Manual
Configuring via Web-based Interface
CHAPTER 4.
CONFIGURING
VIA
WEB-BASED
INTERFACE
Click'n'Connect
To configure a WAN connection, click the
Click'n'Connect
link in the
Net
section.
Figure 24. Configuring a WAN connection.
Connect the Ethernet cable provided by your ISP to the WAN port of the router. Verify the relevant
LED (the
Internet
LED should be on).
Click the
Next
button to continue.
Page
38
of 197
Page 39 / 197
DIR-632
Multifunction Wireless Router Supporting WiMAX,
3G GSM/CDMA with Built-in 8-port Switch
User Manual
Configuring via Web-based Interface
Figure 25. The page for selecting a 3G network operator.
On the opened page, from the
Provider
drop-down list, select your country and operator if you are
going to configure a 3G network connection, or leave the
Manually
value, if you are going to
configure a wired or WiMAX WAN connection or you want to specify all settings for your 3G
WAN connection independently.
Click the
Next
button to continue.
Page
39
of 197
Page 40 / 197
DIR-632
Multifunction Wireless Router Supporting WiMAX,
3G GSM/CDMA with Built-in 8-port Switch
User Manual
Configuring via Web-based Interface
Figure 26. The page for selecting the connection type.
On the opened page, select the needed choice of the radio button and click the
Next
button.
To create a WiMAX WAN connection, on the opened page, select the
USB-WiMAX
choice and
click the
Next
button (the page is displayed only when a WiMAX USB modem is connected to the
router).
Page
40
of 197
19216811.live