1. Home
    2. /
  2. Manuals
    3. /
  3. D-Link
    4. /
  4. DIR-632
    5. /
  5. 12
Page 56 / 197 Scroll up to view Page 51 - 55
DIR-632
Multifunction Wireless Router Supporting WiMAX,
3G GSM/CDMA with Built-in 8-port Switch
User Manual
Configuring via Web-based Interface
Parameter
Description
Encryption
Select a method of MPPE encryption.
•
No encrypt
: MPPE encryption is not applied.
•
MPPE 40/128 bit
: MPPE encryption with a 40-bit or 128-bit
key is applied.
•
MPPE 40 bit
: MPPE encryption with a 40-bit key is applied.
•
MPPE 128 bit
: MPPE encryption with a 128-bit key is
applied.
MPPE encryption can be applied only if the
MS-CHAP
,
MS-
CHAP-V2
, or
AUTO
value is selected from the
Authentication
algorithm
drop-down list.
Authentication
algorithm
Select a required authentication method from the drop-down list or
leave the
AUTO
value.
MTU
The maximum size of units transmitted by the interface.
Keep Alive
Select the checkbox if you want the router to
keep you connected to
the server even when the connection has been inactive for a
specified period of time. When the checkbox is selected, the
LCP
interval
and
LCP fails
fields are available. Specify the required
values.
Extra options
Advanced options of the pppd daemon which need to be specified
for this connection.
Optional
.
Dial on demand
Select the checkbox if you want the router to establish the
connection on demand. In the
Maximum idle time
field, specify a
period of inactivity (in seconds) after which the connection should
be terminated.
Static IP Address
Fill in the field if you want to use a static IP address for this
connection.
PPP debug
Select the checkbox if you want to log
all data on PPP connection
debugging.
IP received
The assigned IP address.
Page
56
of 197
Page 57 / 197
DIR-632
Multifunction Wireless Router Supporting WiMAX,
3G GSM/CDMA with Built-in 8-port Switch
User Manual
Configuring via Web-based Interface
Figure 41. Configuring PPTP WAN connection. The expert settings mode. The
Miscellaneous
section.
Parameter
Description
Miscellaneous
Enable RIP
Select the checkbox to allow using RIP for this connection.
NAT
Select the checkbox if you want one WAN IP address to be used for
all computers of your LAN.
Firewall
Select the checkbox to enable protection against ARP and DDoS
attacks.
Ping
Select the checkbox to allow the router to answer ping requests from
the external network through this connection. For security reasons,
it is recommended not to select this checkbox.
Click the
Next
button to continue.
After that the page displaying all specified settings opens. Click the
Apply
button to create the
connection or the
Back
button to specify other settings.
After clicking the
Apply
button, the page for checking the connection availability opens (see the
Checking Internet Availability
section, page 79).
Page
57
of 197
Page 58 / 197
DIR-632
Multifunction Wireless Router Supporting WiMAX,
3G GSM/CDMA with Built-in 8-port Switch
User Manual
Configuring via Web-based Interface
PPTP + Static IP or L2TP + Static IP Connection
Figure 42. Configuring PPTP + Static IP WAN connection.
Fill in the
IP Address
and
Netmask
fields.
In the
Gateway IP address
field, enter the IP address of the gateway used by this WAN
connection.
In the
Primary DNS server
field, enter the address of the primary DNS server.
If your wired ISP uses authorization via the 802.1x protocol, in the
Authorization via 802.1x
protocol
section, select the
Authorization in the ISP's network via 802.1x protocol
checkbox and fill in the fields of the section in accordance with data provided by your ISP.
As a rule, the specified settings are enough to configure a non-protected connection of the selected
type. If you need to specify additional settings, open the expert settings mode. To do this, use the
switch in the bottom left corner of the page.
Page
58
of 197
Page 59 / 197
DIR-632
Multifunction Wireless Router Supporting WiMAX,
3G GSM/CDMA with Built-in 8-port Switch
User Manual
Configuring via Web-based Interface
Figure 43. Configuring PPTP + Static IP WAN connection. The expert settings mode. The
Ethernet
section.
Parameter
Description
Ethernet
MTU
The maximum size of units transmitted by the interface.
MAC
A MAC address assigned to the interface. This parameter is
mandatory if your ISP uses MAC address binding. In the field, enter
the MAC address registered by your ISP upon concluding the
agreement.
You can click the
Clone MAC
Address
button (
) to set the
MAC address of the network interface card (of the computer that is
being used to configure the router at the moment) as the MAC
address of the WAN interface.
Also you can set the address of a device connected to the router's
LAN at the moment. To do this, select the relevant value from the
drop-down list (the field will be filled in automatically).
Page
59
of 197
Page 60 / 197
DIR-632
Multifunction Wireless Router Supporting WiMAX,
3G GSM/CDMA with Built-in 8-port Switch
User Manual
Configuring via Web-based Interface
Figure 44.
Configuring PPTP + Static IP WAN connection. The expert settings mode. The
IP
and
Authorization via 802.1x protocol
sections.
Parameter
Description
IP
IP Address
Enter an IP address for this WAN connection.
Netmask
Enter a subnet mask for this WAN connection.
Gateway IP address
Enter an IP address of the gateway used by this WAN connection.
Primary DNS server/
Secondary DNS server
Enter addresses of the primary and secondary DNS servers in the
relevant fields.
Authorization via 802.1x protocol
Authorization in the
ISP's network via
802.1x protocol
Select the checkbox to allow authorization in the ISP's network via
the 802.1x protocol.
Authentication method
Select a needed authentication method from the drop-down list.
Username
Enter the username provided by your ISP.
Password
Enter the password provided by your ISP.
Page
60
of 197

Rate

3.5 / 5 based on 2 votes.

Popular D-Link Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top