Page 46 / 197
Scroll up to view Page 41 - 45
DIR-632
Multifunction Wireless Router Supporting WiMAX,
3G GSM/CDMA with Built-in 8-port Switch
User Manual
Configuring via Web-based Interface
Static IP Connection
Figure 31. Configuring Static IP WAN connection.
In the
Connection name
field, specify a name for the connection for easier identification.
Fill in the
IP Address
and
Netmask
fields.
In the
Gateway IP address
field, enter the IP address of the gateway used by this WAN
connection.
In the
Primary DNS server
field, enter the address of the primary DNS server.
If your wired ISP uses authorization via the 802.1x protocol, in the
Authorization via 802.1x
protocol
section, select the
Authorization in the ISP's network via 802.1x protocol
checkbox and fill in the fields of the section in accordance with data provided by your ISP.
As a rule, the specified settings are enough to configure a connection of the selected type. If you
need to specify additional settings, open the expert settings mode. To do this, use the switch in the
bottom left corner of the page.
Page
46
of 197
Page 47 / 197
DIR-632
Multifunction Wireless Router Supporting WiMAX,
3G GSM/CDMA with Built-in 8-port Switch
User Manual
Configuring via Web-based Interface
Figure 32. Configuring Static IP WAN connection. The expert settings mode. The
Ethernet
section.
Parameter
Description
Connection name
A name for connection for easier identification.
Ethernet
MTU
The maximum size of units transmitted by the interface.
MAC
A MAC address assigned to the interface. This parameter is
mandatory if your ISP uses MAC address binding. In the field, enter
the MAC address registered by your ISP upon concluding the
agreement.
You can click the
Clone MAC Address
button
(
) to set the
MAC address of the network interface card (of the computer that is
being used to configure the router at the moment) as the MAC
address of the WAN interface.
Also you can set the address of a device connected to the router's
LAN at the moment. To do this, select the relevant value from the
drop-down list (the field will be filled in automatically).
Page
47
of 197
Page 48 / 197
DIR-632
Multifunction Wireless Router Supporting WiMAX,
3G GSM/CDMA with Built-in 8-port Switch
User Manual
Configuring via Web-based Interface
Figure 33. Configuring Static IP WAN connection. The expert settings mode. The
IP
and
Authorization via
802.1x protocol
sections.
Parameter
Description
IP
IP Address
Enter an IP address for this WAN connection.
Netmask
Enter a subnet mask for this WAN connection.
Gateway IP address
Enter an IP address of the gateway used by this WAN connection.
Primary DNS server/
Secondary DNS server
Enter addresses of the primary and secondary DNS servers in the
relevant fields.
Authorization via 802.1x protocol
Authorization in the
ISP's network via
802.1x protocol
Select the checkbox to allow authorization in the ISP's network via
the 802.1x protocol.
Authentication method
Select a needed authentication method from the drop-down list.
Username
Enter the username provided by your ISP.
Password
Enter the password provided by your ISP.
Page
48
of 197
Page 49 / 197
DIR-632
Multifunction Wireless Router Supporting WiMAX,
3G GSM/CDMA with Built-in 8-port Switch
User Manual
Configuring via Web-based Interface
Figure 34. Configuring Static IP WAN connection. The expert settings mode. The
Miscellaneous
section.
Parameter
Description
Miscellaneous
Enable RIP
Select the checkbox to allow using RIP for this connection.
Enable IGMP Multicast
Select the checkbox to allow multicast traffic from the external
network (e.g. video streaming) to be received.
NAT
Select the checkbox if you want one WAN IP address to be used for
all computers of your LAN.
Firewall
Select the checkbox to enable protection against ARP and DDoS
attacks.
Ping
Select the checkbox to allow the router to answer ping requests from
the external network through this connection. For security reasons,
it is recommended not to select this checkbox.
Click the
Next
button to continue.
After that the page displaying all specified settings opens. Click the
Apply
button to create the
connection or the
Back
button to specify other settings.
After clicking the
Apply
button, the page for checking the Internet availability opens (see the
Checking Internet Availability
section, page 79).
Page
49
of 197
Page 50 / 197
DIR-632
Multifunction Wireless Router Supporting WiMAX,
3G GSM/CDMA with Built-in 8-port Switch
User Manual
Configuring via Web-based Interface
Dynamic IP Connection
Figure 35. Configuring Dynamic IP WAN connection.
In the
Connection name
field, specify a name for the connection for easier identification.
If your ISP has provided the addresses of the DNS servers, deselect the
Obtain DNS server
addresses automatically
checkbox and fill in the
Primary DNS server
field.
As a rule, the specified settings are enough to configure a connection of the selected type. If you
need to specify additional settings, open the expert settings mode. To do this, use the switch in the
bottom left corner of the page.
Page
50
of 197
19216811.live