Page 186 / 197
Scroll up to view Page 181 - 185
DIR-632
Multifunction Wireless Router Supporting WiMAX,
3G GSM/CDMA with Built-in 8-port Switch
User Manual
Configuring via Web-based Interface
Firmware Upgrade
On the
System / Firmware upgrade
page, you can upgrade the firmware of the router.
!
Upgrade the firmware only when the router is connected to your PC via a wired
connection.
Figure 149. The
System / Firmware upgrade
page.
The current version of the router's firmware is displayed in the
Firmware version
field located
next the D-Link logo in the top left corner of the page. If you need to install a newer version of the
firmware, follow the next steps:
!
Attention! Do not turn off the router before the firmware upgrade is completed. This may
cause the device breakdown.
1.
Download a new version of the firmware from
www.dlink.ru
.
2.
Click the
Choose/Browse
8
button on the
System / Firmware upgrade
page to locate
the new firmware file.
3.
Click the
Update
button to upgrade the firmware of the router.
4.
Wait until the router is rebooted (about one and a half or two minutes).
5.
Log into the web-based interface using the login (
admin
) and the current password.
8
The name of the button depends upon the web browser that you use.
Page
186
of 197
Page 187 / 197
DIR-632
Multifunction Wireless Router Supporting WiMAX,
3G GSM/CDMA with Built-in 8-port Switch
User Manual
Configuring via Web-based Interface
6.
Select the
Factory
line in the top-page menu displayed when the mouse pointer is over the
System
caption.
7.
Wait until the router is rebooted. Log into the web-based interface, using the default IP
address, login and password (
192.168.0.1
,
admin
,
admin
).
Page
187
of 197
Page 188 / 197
DIR-632
Multifunction Wireless Router Supporting WiMAX,
3G GSM/CDMA with Built-in 8-port Switch
User Manual
Configuring via Web-based Interface
NTP Client
On the
System / NTP client
page, you can configure automatic synchronization of the system
time with a time server on the Internet.
Figure 150. The
System / NTP client
page.
To enable automatic synchronization with a time server:
1.
Select the
Enabled
checkbox.
2.
Select your time zone.
3.
Specify the needed NTP server in the
NTP servers
field or leave the server specified by
default.
4.
Click the
Change
button.
!
When the router is powered off or rebooted, the system time is reset to the default value.
If you have set automatic synchronization for the system time, the internal clock of the
device will be configured after connecting to the Internet.
Page
188
of 197
Page 189 / 197
DIR-632
Multifunction Wireless Router Supporting WiMAX,
3G GSM/CDMA with Built-in 8-port Switch
User Manual
Configuring via Web-based Interface
Traceroute
On the
System / Traceroute
page, you can define the route of data transfer to a host via the
traceroute utility.
Figure 151. The
System / Traceroute
page.
To define the route, enter the name or IP address of a host in the
Host
field and click the
Start
button. After a while, the results will be displayed on the page.
Page
189
of 197
Page 190 / 197
DIR-632
Multifunction Wireless Router Supporting WiMAX,
3G GSM/CDMA with Built-in 8-port Switch
User Manual
Configuring via Web-based Interface
Telnet
On the
System / Telnet
page, you can enable or disable access to the device settings via TELNET
from your LAN. By default, access is enabled.
Figure 152. The
System / Telnet
page.
To disable access via TELNET, deselect the
On
checkbox and click the
Change
button.
To enable access via TELNET again, select the
On
checkbox. In the
Port
field, enter the number of
the router's port through which access will be allowed (by default, the port
23
is specified). Then
click the
Change
button.
Page
190
of 197
19216811.live