D-Link DIR-632 Router Manual PDF (Setup & Configuration Guide)

Page 136 / 197 Scroll up to view Page 131 - 135

DIR-632

Multifunction Wireless Router Supporting WiMAX,

3G GSM/CDMA with Built-in 8-port Switch

User Manual

Configuring via Web-based Interface

Figure 111. The tab for adding a MAC address.

Enter an address in the

MAC address

field of the

MAC address adding

section and click the

Add

button.

To remove a MAC address from the list of MAC addresses, select the checkbox located to the right

of the relevant MAC address in the

MAC address list

section and click the

Delete

button.

Page

136

of 197

Page 137 / 197

DIR-632

Multifunction Wireless Router Supporting WiMAX,

3G GSM/CDMA with Built-in 8-port Switch

User Manual

Configuring via Web-based Interface

Station List

On the

Wi-Fi / Station List

page, you can view the list of wireless clients connected to the router.

Figure 112. The list of the wireless clients.

To view the latest data on the devices connected to the WLAN, click the

Refresh

button.

Page

137

of 197

Page 138 / 197

DIR-632

Multifunction Wireless Router Supporting WiMAX,

3G GSM/CDMA with Built-in 8-port Switch

User Manual

Configuring via Web-based Interface

WPS

On the

Wi-Fi / WPS

page, you can enable the function for secure configuration of the WLAN and

select a method used to easily add wireless devices to the WLAN.

The WPS function helps to configure the protected wireless network automatically. Devices

connecting to the wireless network via the WPS function must support the WPS function.

!

Before using the function you need to configure one of the following authentication types:

Open

with no encryption,

WPA-PSK

, or

WPA2-PSK

with the

AES

or

TKIP+AES

encryption method (on the

Wi-Fi / Security settings

page).

Figure 113. The page for configuring the WPS function.

Page

138

of 197

Page 139 / 197

DIR-632

Multifunction Wireless Router Supporting WiMAX,

3G GSM/CDMA with Built-in 8-port Switch

User Manual

Configuring via Web-based Interface

To activate the WPS function, select the

WPS Enable

checkbox and click the

Change

button.

When the checkbox is selected, the

Information

and

Connection

sections are available on the

page.

Parameter

Description

Default PIN code

The PIN code of the router. This parameter is used when connecting

the router to a registrar to set the parameters of the WPS function.

WPS Status

The state of the WPS function:

•

Configured

(all needed settings are specified)

•

Unconfigured

(you need to specify the relevant settings).

SSID

The name of the router's WLAN.

Network Authentication

The network authentication type specified for the WLAN.

Encryption

The encryption type specified for the WLAN.

Encryption key

The encryption key specified for the WLAN.

Refresh

Click the button to refresh the data on the page.

Reset to unconfigured

Click the button to reset the parameters of the WPS function.

WPS Method

A method of the WPS function. Select a value from the drop-down

list.

: Connecting the device via the PIN code.

PBC

: Connecting the device via the push button (actual or virtual).

PIN Code

The PIN code of the WPS-enabled device that needs to be connected

to the wireless network of the router.

The field is displayed only when the

value is selected from the

WPS Method

drop-down list.

Connect

Click the button to connect the wireless device to the router's WLAN

via the WPS function.

Page

139

of 197

Page 140 / 197

DIR-632

Multifunction Wireless Router Supporting WiMAX,

3G GSM/CDMA with Built-in 8-port Switch

User Manual

Configuring via Web-based Interface

Using WPS Function via Web-based Interface

To add a wireless device via the PIN method of the WPS function, follow the next steps:

1.

Select the

WPS

Enable

checkbox.

2.

Click the

Change

button.

3.

Select the

value from the

WPS

Method

drop-down list.

4.

Select the PIN method in the software of the wireless device that you want to connect to the

router's WLAN.

5.

Click the relevant button in the software of the wireless device that you want to connect to

the WLAN.

6.

Right after that, enter the PIN code specified on the cover of the wireless device or in its

software in the

PIN Code

field.

7.

Click the

Connect

button in the web-based interface of the router.

To add a wireless device via the PBC method of the WPS function, follow the next steps:

1.

Select the

WPS

Enable

checkbox.

2.

Click the

Change

button.

3.

Select the

PBC

value from the

WPS Method

drop-down list.

4.

Select the PBC method in the software of the wireless device that you want to connect to the

router's WLAN.

5.

Click the relevant button in the software or press the WPS button on the cover of the

wireless device that you want to connect to the WLAN.

6.

Click the

Connect

button in the web-based interface of the router.

Using WPS Function without Web-based Interface

You can add a wireless device to the router's WLAN without accessing the web-based interface of

the router. To do this, you need to configure the following router's settings:

1.

Specify corresponding security settings for the wireless network of the router.

2.

Select the

WPS

Enable

checkbox.

3.

Click the

Change

button.

4.

Save the settings and close the web-based interface (click the

Save

line in the top-page

menu displayed when the mouse pointer is over the

System

caption, then click the

Logout

line).

Page

140

of 197

Rate

Popular D-Link Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share