Page 66 / 93
Scroll up to view Page 61 - 65
62
D-Link DIR-605L User Manual
Section 4 - Security
WPA/WPA2
It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your
wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used.
2.
.
Highlight the wireless network (SSID) you would like to connect
to and click
Connect
.
1.
.
Open the Windows Vista® Wireless Utility by right-clicking on the
wireless computer icon in your system tray (lower right corner of
screen). Select
Connect.to.a.network
.
Page 67 / 93
63
D-Link DIR-605L User Manual
Section 4 - Security
3.
Enter the same security key or passphrase that is on your router and
click
Connect
.
It may take 20-30 seconds to connect to the wireless network. If the
connection fails, please verify that the security settings are correct. The
key or passphrase must be exactly the same as on the wireless router.
Page 68 / 93
64
D-Link DIR-605L User Manual
Section 4 - Security
WPS/WCN 2.0
The router supports Wi-Fi protection, referred to as WCN 2.0 in Windows Vista®. The following instructions for setting this up
depends on whether you are using Windows Vista® to configure the router or third party software.
When you first set up the router, Wi-Fi protection is disabled and unconfigured. To enjoy the benefits of Wi-Fi protection, the
router must be both enabled and configured. There are three basic methods to accomplish this: use Windows Vista’s built-in
support for WCN 2.0, use software provided by a third party, or manually configure.
If you are running Windows Vista®, log into the router and click the
Enable
checkbox in the
Basic
>
Wireless
section. Use the
Current PIN that is displayed on the
Advanced
>
Wi-Fi.Protected.Setup
section or choose to click the
Generate.New.PIN
button or
Reset.PIN.to.Default
button.
If you are using third party software to set up Wi-Fi Protection, carefully follow the directions. When you are finished, proceed
to the next section to set up the newly-configured router.
Page 69 / 93
65
D-Link DIR-605L User Manual
Section 5 - Connecting to a Wireless Network
Windows® XP
Windows® XP users may use the built-in wireless utility (Zero Configuration Utility). The following instructions are for Service
Pack 2 users. If you are using another company’s utility, please refer to the user manual of your wireless adapter for help with
connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows® XP utility as seen below.
Right-click on the wireless computer icon in your system tray
(lower-right corner next to the time). Select
View Available
Wireless Networks
.
If you receive the
Wireless Networks Detected
bubble, click on
the center of the bubble to access the utility.
or
The utility will display any available wireless networks in your area.
Click on a network (displayed using the SSID) and click the
Connect
button.
If you get a good signal but cannot access the Internet, check you
TCP/IP settings for your wireless adapter. Refer to the
Networking
Basics
section in this manual for more information.
Page 70 / 93
66
D-Link DIR-605L User Manual
Section 5 - Connecting to a Wireless Network
It is recommended to enable WPA on your wireless router or access point before configuring your wireless adapter. If you are
joining an existing network, you will need to know the WPA key being used.
2. Highlight the wireless network (SSID) you would like to
connect to and click
Connect
.
1.
Open the Windows® XP Wireless Utility by right-clicking on the
wireless computer icon in your system tray (lower-right corner
of screen). Select
View.Available.Wireless.Networks
.
WPA/WPA2
19216811.live