Page 56 / 97 Scroll up to view Page 51 - 55
56
D-Link DIR-600 User Manual
Section 4 - Security
Configure WEP
It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish
wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to
the added overhead.
1.
Log into the web-based con±guration by opening a web browser and entering the IP address of the router (192.168.0.1).
Click on
Wireless Setup
on the left side.
2.
Next to
Security Mode
, select Enable WEP Wireless Security (basic).
3.
Next to
Authentication
, select either Shared Key or Open.
Shared Key is recommended as it provides greater security
when WEP is enabled.
4.
Select either 64Bit or 128Bit encryption from the drop-down
menu next to
WEP Encryption
.
5.
Next to
Default฀Key฀Type
, select WEP Key 1 and enter a WEP
key that you create. Make sure you enter this key exactly on
all your wireless devices. You may enter up to four different
keys either using Hex or ASCII. Hex is recommended (letters
A-F and numbers 0-9 are valid). In ASCII all numbers and letters
are valid.
6.
Click
Save฀ Settings
to save your settings. If you are con±guring the router with a wireless adapter, you will lose
connectivity until you enable WEP on your adapter and enter the same WEP key as you did on the router.
Page 57 / 97
57
D-Link DIR-600 User Manual
Section 4 - Security
What is WPA?
WPA, or Wi-Fi Protected Access, is a Wi-Fi standard that was designed to improve the security features of WEP (Wired
Equivalent Privacy).
The two major improvements over WEP:
• Improved data encryption through the Temporal Key Integrity Protocol (TKIP). TKIP scrambles the keys
using a hashing algorithm and, by adding an integrity-checking feature, ensures that the keys haven’t
been tampered with. WPA2 is based on 802.11i and uses Advanced Encryption Standard (AES) instead
of TKIP.
• User authentication, which is generally missing in WEP, through the extensible authentication protocol
(EAP). WEP regulates access to a wireless network based on a computer’s hardware-specific MAC
address, which is relatively simple to be sni²ed out and stolen. EAP is built on a more secure public-key
encryption system to ensure that only authorized network users can access the network.
WPA-PSK/WPA2-PSK uses a passphrase or key to authenticate your wireless connection. The key is an alpha-numeric
password between 8 and 63 characters long. The password can include symbols (!?*&_) and spaces. This key must
be the exact same key entered on your wireless router or access point.
WPA/WPA2 incorporates user authentication through the Extensible Authentication Protocol (EAP). EAP is built on a
more secure public key encryption system to ensure that only authorized network users can access the network.
Page 58 / 97
58
D-Link DIR-600 User Manual
Section 4 - Security
Configure WPA/WPA2-PSK
It is recommended to enable encryption on your wireless Router before your wireless network adapters. Please establish
wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to
the added overhead.
1.
Log into the web-based con±guration by opening a web browser
and entering the IP address of the router (192.168.0.1). Click on
Wireless Setup
on the left side.
2.
Next to
Security Mode
, select Enable WPA/WPA2 Wireless
Security (enhanced).
3.
Next to
Cipher Mode
, select TKIP,
AES,
or
Auto.
4.
Next to
PSK/EAP
, select PSK.
5.
Next to
Network Key
, enter a key (passphrase). The key is an alpha-numeric password
between 8 and 63 characters long. The password can include symbols (!?*&_) and spaces.
Make sure you enter this key exactly the same on all other wireless clients.
6.
Click
Save฀ Settings
to save your settings. If you are con±guring the Router with a wireless adapter, you will lose
connectivity until you enable WPA/WPA2-PSK on your adapter and enter the same passphrase as you did on the
Router.
Page 59 / 97
59
D-Link DIR-600 User Manual
Section 4 - Security
Con±gure฀WPA/WPA2฀(RADIUS)
It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish
wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to
the added overhead.
1.
Log into the web-based con±guration by opening a web browser and entering the IP address of the router (192.168.0.1).
Click on
Wireless Settings
on the left side.
2.
Next to
Security Mode
, select Enable WPA Only Wireless Security (enhanced), Enable WPA2 Only Wireless Security
(enhanced), or Enable WPA/WPA2 Wireless Security (enhanced).
3.
Next to
Cipher Type
, select TKIP, AES,
or
Auto.
4.
Next to
PSK/EAP
, select EAP.
5.
Next to
RADIUS฀Server฀1
enter the
IP Address
of
your RADIUS server.
6.
Next to
Port
, enter the port you are using with your
RADIUS server. 1812 is the default port.
7.
Next to
Shared Secret
, enter the security key.
8.
If you have a secondary RADIUS server, enter its IP
address, port, and secret key.
9.
Click
Save฀Settings
to save your settings.
Page 60 / 97
60
D-Link DIR-600 User Manual
Section 5 - Connecting to a Wireless Network
Connect to a Wireless Network
Using Windows
®
XP
Windows
®
XP users may use the built-in wireless utility (Zero Con±guration Utility). The following instructions are for
Service Pack 2 users. If you are using another company’s utility or Windows
®
2000, please refer to the user manual
of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option
similar to the Windows
®
XP utility as seen below.
Right-click on the wireless computer icon in your system tray
(lower-right corner next to the time). Select
View฀ Available฀
Wireless Networks
.
If you receive the
Wireless฀Networks฀Detected
bubble, click
on the center of the bubble to access the utility.
or
The utility will display any available wireless networks in your
area. Click on a network (displayed using the SSID) and click
the
Connect
button.
If you get a good signal but cannot access the Internet,
check you TCP/IP settings for your wireless adapter. Refer
to the
Networking Basics
section in this manual for more
information.

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top