Page 16 / 27 Scroll up to view Page 11 - 15
DIR-300NRU
Quick Installation Guide
Configuring Connection to the Internet
!
You should configure your WAN connection in accordance with data
provided by your
Internet service provider (ISP). Make sure that you
have obtained all necessary information prior to configuring your
connection. Otherwise contact your ISP.
Configuring WAN Connection
1.
Go to the
Net
/
WAN
page, select the
WAN
connection and click the
Delete
button.
2.
Click the
Add
button.
3.
In the
General settings
section, select a needed value from the
Connection Type
drop-down list.
4.
From the
Port
drop-down list, select the
Ports:5
value.
5.
Specify a name for your connection (any name for easier identification) in
the
Name
field.
16
Page 17 / 27
DIR-300NRU
Quick Installation Guide
6.
If your ISP uses MAC address binding, in the
Ethernet
section, in the
MAC
field, enter the MAC address registered by your ISP upon
concluding the agreement. To set the MAC address of the network
interface card (of the computer that is being used to configure the router
at the moment) as the MAC address of the WAN interface, click the
Clone MAC
button. To set the address of a device connected to the
router's LAN at the moment, select the relevant value from the drop-down
list located to the right of the field.
7.
For connection of PPPoE type:
in the
PPP
section, enter authorization
data provided by your ISP (the username (login) in the
Username
field
and the password in the
Password
and
Password confirmation
fields), or select the
Without authorization
checkbox if authorization
is not required.
17
Page 18 / 27
DIR-300NRU
Quick Installation Guide
8.
For connection of Static IP type
: in the
IP
section, fill in the
IP
Address
,
Netmask
,
Gateway IP address
, and
Primary DNS
server
fields.
9.
For connection of Dynamic IP type
: if your ISP has provided the address
of the DNS server, in the
IP
section, deselect the
Obtain DNS server
addresses automatically
checkbox and fill in the
Primary DNS
server
field.
18
Page 19 / 27
DIR-300NRU
Quick Installation Guide
10.
For connection of PPTP + Static IP or L2TP + Static IP type
: in the
IP
section, fill in the
IP Address
,
Netmask
,
Gateway IP address
, and
Primary DNS server
fields. Then in the
VPN
section,
enter
authorization data provided by your ISP (the username (login) in the
Username
field and the password in the
Password
and
Password
confirmation
fields), or select the
Without authorization
checkbox if
authorization is not required. In the
VPN s
erver address
field, enter
the IP or URL address of the PPTP or L2TP authentication server. If your
ISP applies encryption, select a needed value from the
Encryption
drop-
down list.
19
Page 20 / 27
DIR-300NRU
Quick Installation Guide
11.
For connection of PPTP + Dynamic IP or L2TP + Dynamic IP type
: if
your ISP has provided the address of the DNS server, in the
IP
section,
deselect the
Obtain DNS server addresses automatically
checkbox and fill in the
Primary DNS server
field. Then in the
VPN
section, enter authorization data provided by your ISP (the username
(login) in the
Username
field and the password in the
Password
and
Password confirmation
fields), or select the
Without authorization
checkbox if authorization is not required. In the
VPN server address
field, enter the IP or URL address of the PPTP or L2TP authentication
server. If your ISP applies encryption, select a needed value from the
Encryption
drop-down list.
12.
If needed, fill in other fields on the page in accordance with data provided
by the ISP.
13.
Click the
Save
button.
20

Rate

3.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top