1. Home
    2. /
  2. Manuals
    3. /
  3. D-Link
    4. /
  4. DIR-130
    5. /
  5. 3
Page 11 / 83 Scroll up to view Page 6 - 10
µ
D-L±nk DIR-130 User Manual
Sect±on ² - Installat±on
Before you Begin
Installation
This section will walk you through the installation process.
Please configure the router with the computer that was last connected directly to your modem. Also, you can only use
the Ethernet port on your modem. If you were using the USB connection before using the router, then you must turn off
your modem, disconnect the USB cable and connect an Ethernet cable to the Internet port on the router, and then turn
the modem back on. In some cases, you may need to call your ISP to change connection types (USB to Ethernet).
If you have DSL and are connecting via PPPoE, make sure you disable or uninstall any PPPoE software such as
WinPoet, Broadjump, or Enternet 300 from your computer or you will not be able to connect to the Internet.
Page 12 / 83
D-L±nk DIR-130 User Manual
Sect±on ² - Installat±on
If you are connecting the router to a cable/DSL/satellite modem, please follow the steps below:
1. Place the router in an open and central location. Do not plug the power adapter into the router.
2. Turn the power off on your modem. If there is no on/off switch, then unplug the modem’s power adapter. Shut down
your computer.
3. Unplug the Ethernet cable (that connects your computer to your modem) from your computer and place it into the
Internet port on the router.
4. Plug an Ethernet cable into one of the four LAN ports on the router. Plug the other end into the Ethernet port on your
computer.
5. Turn on or plug in your modem.
Wait for the modem to boot (about 30 seconds).
6. Plug the power adapter to the router and connect to an outlet or power strip. Wait about 30 seconds for the router
to boot.
7. Turn on your computer.
8. Verify the link lights on the router. The power light, Internet light, and the LAN light (the port that your computer is
plugged into) should be lit. If not, make sure your computer, modem, and router are powered on and verify the cable
connections are correct.
9. Refer to page 10 to configure your router.
Connect to Cable/DSL/Satellite Modem
Page 13 / 83
·
D-L±nk DIR-130 User Manual
Sect±on ² - Installat±on
If you are connecting the D-Link router to another router to use as a switch, you will have to do the following before
connecting the router to your network:
• Disable UPnP
™
• Disable DHCP
• Change the LAN IP address to an available address on your network. The LAN ports on the router cannot
accept a DHCP address from your other router.
To connect to another router, please follow the steps below:
1. Plug the power into the router. Connect one of your computers to the router (LAN port) using an Ethernet cable.
Make sure your IP address on the computer is 192.168.0.xxx (where xxx is between 2 and 254). Please see the
Networking Basics
section for more information. If you need to change the settings, write down your existing settings
before making any changes. In most cases, your computer should be set to receive an IP address automatically in
which case you will not have to do anything to your computer.
2. Open a web browser and enter
and press
Enter
. When the login window appears, set the user
name to
Admin
and leave the password box empty. Click
Log In
to continue.
3. Click on
Advanced
and then click
Advanced Network
. Uncheck the Enable UPnP checkbox. Click
Save Settings
to continue.
4. Click
Setup
and then click
Network Settings
. Uncheck the Enable DHCP Server server checkbox. Click
Save
Settings
to continue.
5. Under Router Settings, enter an available IP address and the subnet mask of your network. Click
Save Settings
to
save your settings. Use this new IP address to access the configuration utility of the router in the future. Close the
browser and change your computer’s IP settings back to the original values as in Step 1.
Connect to Another Router
Page 14 / 83
¸
D-L±nk DIR-130 User Manual
Sect±on ² - Installat±on
6. Disconnect the Ethernet cable from the router and reconnect your computer to your network.
7. Connect an Ethernet cable in one of the LAN ports of the router and connect it to your other router. Do not plug
anything into the Internet port of the D-Link router.
8. You may now use the other 7 LAN ports to connect other Ethernet devices and computers.
Page 15 / 83
10
D-L±nk DIR-130 User Manual
Sect±on 3 - Configurat±on
Configuration
This section will show you how to configure your new D-Link router using the web-based configuration utility.
Web-based Configuration Utility
To access the configuration utility, open a web-browser
such as Internet Explorer and enter the IP address of
the router (192.168.0.1).
Enter
admin
as the User name field and enter the
password in the Password field. Leave the password
blank by default.
If you get a
Page Cannot be Displayed
error, please
refer to the
Troubleshooting
section for assistance.

Rate

3.5 / 5 based on 2 votes.

Popular D-Link Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top