D-Link DI-804HV Router Manual PDF (Setup & Configuration Guide)

Page 46 / 145 Scroll up to view Page 41 - 45

46

Using the Configuration Menu

Advanced > Application

Some applications require multiple connections, such as Internet gaming, video

conferencing, Internet telephony and others. These applications have difficulties working

through NAT (Network Address Translation).

Special Applications

makes some of these

applications work with the DI-804HV. If you need to run applications that require multiple

connections, specify the port normally associated with an application in the

Trigger

field, then enter the public ports associated with the trigger port into the

Incoming

Ports

field.

At the bottom of the screen, there are already defined special applications. To use

them, select one from the drop down list and select an ID number you want to use.

Then click the “Copy to” button and the router will fill in the appropriate information to

the list. You will then need to enable the service. If the mechanism of Special Applica-

tions fails to make an application work, try using DMZ host instead.

Note!

Only one PC can use each Special Application tunnel.

Trigger Port-

This is the port used to trigger the application. It can be either

a single port or a range of ports.

Public Ports-

This is the port number on the WAN side that will be used to

access the application. You may define a single port or a range

of ports. You can use a comma to add multiple ports or port

ranges.

Enabled-

Select to activate the policy

Page 47 / 145

47

Using the Configuration Menu

Advanced > IP Filter

IP Filter-

Use IP Filters to deny LAN IP addresses access to the internet

Schedule-

IP Address-

Enter in the IP address range of the computers that you want the policy to apply to.

If it

is only a single computer that you want the policy applied to, then enter the IP address of

that computer in the Start Source IP and leave the End Source IP blank.

Use IP (Internet Protocol)

filters to allow or deny

computers access to the

Internet based on their IP

address.

Port Range-

Enter in the port range of the TCP/UDP ports that you want the policy to apply to.

If it is

only a single port

that you want the policy applied to, then enter the port number in the

Start Port

field and leave the End Port field blank.

If you want to use all the ports, you

can leave the port range empty.

Enabled or Disabled-

Click

Enabled

to apply the filter policy or click

Disabled

to enter an inactive filter policy

(You can reactivate the policy later.)

Select

Always

, or choose

From

and enter the time period during which the IP filter policy

will be in effect.

Page 48 / 145

48

Using the Configuration Menu

Advanced > MAC Filters

MAC (Media Access Control) Filters are used to deny or allow LAN (Local Area Network)

computers from accessing the Internet and network by their MAC address.

At the bottom of the screen, there is a list of MAC addresses from the DHCP client

computers connected to the DI-804HV. To use them, select one from the drop down list.

Then click the “Apply” button and the DI-804HV will fill in the appropriate information to

the list.

Disabled MAC Filter-

Select this option if you do not want to use MAC filters.

Only allow computers with MAC address listed below to access the network-

Select this option to only allow computers that are in the list

to access the network and Internet. All other computers will

be denied access to the network and Internet.

Only deny computers with MAC address listed below to access the network-

Select this option to only deny computers that are in the list

to access the network and Internet. All other computers will

be allowed access to the network and Internet.

Enter the

MAC Address

of the client that will be filtered

MAC Address-

Page 49 / 145

49

Using the Configuration Menu

Advanced > URL Blocking

Use URL Blocking to deny LAN computers from accessing specific web sites by its

URL. A URL is a specially formatted text string that defines a location on the Internet.

If any part of the URL contains the blocked word, the site will not be accessible and

the web page will not display.

Disabled URL Blocking-

Select this option if you do not want to use URL Blocking.

Page 50 / 145

50

Using the Configuration Menu

Advanced > Domain Blocking

Use Domain Blocking to allow or deny computers access to specific Internet domains

whether it is through www, ftp, snmp, etc.

Disabled Domain Blocking-

Select this option if you do not want to use Domain Blocking.

Allow users to access all domains except “Blocked Domains”-

Select this option to allow users to access the specified Internet domains listed below.

Users will be denied access to all other Internet domains.

Deny users to access all domains except “Permitted Domains”-

Select this option to deny users to access the specified Internet domains listed below.

Users will be allowed access to all other Internet domains.

Rate

Popular D-Link Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share