²±

D-Link DGL-4500 User Manual

Section ³ - Configuration

The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not

recommended that you change the default MAC address unless required by your ISP.

You can use the

Clone.Your.PC’s.

MAC.Address

button to replace the Internet port’s MAC address with the MAC address of your Ethernet card.

MAC Address:

²²

D-Link DGL-4500 User Manual

Section ³ - Configuration

Select

PPPoE.(Username/Password)

from the drop-down menu.

Select

Static

if your ISP assigned you the IP address, subnet mask,

gateway, and DNS server addresses. In most cases, select

Dynamic

.

Enter the IP address (Static PPPoE only).

Enter your PPPoE user name.

Enter your PPPoE password and then retype the password in the next

box.

Enter the ISP Service Name (optional).

Select either

Always-on

,

On-Demand

, or

Manual

.

Enter the Primary and Secondary DNS Server Addresses (On-Demand

only).

Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature,

enable Auto-reconnect.

Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1492 is

the default MTU.

The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not

recommended that you change the default MAC address unless required by your ISP.

You can use the

Clone.Your.PC’s.

MAC.Address

button to replace the Internet port’s MAC address with the MAC address of your Ethernet card.

My Internet

Connection:

Address Mode:

IP Address:

User Name:

Password

:

Service Name:

Reconnection Mode:

Maximum Idle Time:

DNS Addresses:

MTU:

MAC Address:

Internet Setup

PPPoE (DSL)

Choose PPPoE (Point to Point Protocol over Ethernet) if your ISP uses a PPPoE connection. Your ISP will provide

you with a username and password. This option is typically used for DSL services. Make sure to remove your PPPoE

software from your computer. The software is no longer needed and will not work through a router.

²³

D-Link DGL-4500 User Manual

Section ³ - Configuration

Select

Static

if your ISP assigned you the IP address,

subnet mask, gateway, and DNS server addresses. In most

cases, select

Dynamic

.

Enter the IP address (Static PPTP only).

Enter the Primary and Secondary DNS Server Addresses

(Static PPTP only).

Enter the Gateway IP Address provided by your ISP.

Enter the Server IP provided by your ISP (optional).

Enter your PPTP username.

Enter your PPTP password and then retype the password

in the next box.

Select either

Always-on

,

On-Demand

, or

Manual

.

Enter a maximum idle time during which the Internet

connection is maintained during inactivity. To disable this

feature, enable Always-on.

The DNS server information will be supplied by your ISP

(Internet Service Provider.)

Address Mode:

PPTP IP Address:

PPTP Subnet

Mask:

PPTP Gateway:

PPTP Server IP:

Internet Setup

PPTP

Choose PPTP (Point-to-Point-Tunneling Protocol ) if your ISP uses a PPTP connection. Your ISP will provide you with

a username and password. This option is typically used for DSL services.

Username:

Password:

Reconnect Mode:

Maximum Idle

Time:

DNS Servers:

²4

D-Link DGL-4500 User Manual

Section ³ - Configuration

Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1400 is

the default MTU.

The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not

recommended that you change the default MAC address unless required by your ISP.

You can use the

Clone.Your.PC’s.

MAC.Address

button to replace the Internet port’s MAC address with the MAC address of your Ethernet card.

MTU:

MAC Address:

²5

D-Link DGL-4500 User Manual

Section ³ - Configuration

Select

Static

if your ISP assigned you the IP address,

subnet mask, gateway, and DNS server addresses. In

most cases, select

Dynamic

.

Enter the L2TP IP address supplied by your ISP (Static

only).

Enter the Subnet Mask supplied by your ISP (Static

only).

Enter the Gateway IP Address provided by your ISP.

Enter the Server IP provided by your ISP (optional).

Enter your L2TP username.

Enter your L2TP password and then retype the password

in the next box.

Select either

Always-on

,

On-Demand

, or

Manual

.

Enter a maximum idle time during which the Internet

connection is maintained during inactivity. To disable this

feature, enable Always-on.

Enter the Primary and Secondary DNS Server Addresses

(Static L2TP only).

Address Mode:

L2TP IP Address:

L2TP Subnet Mask:

L2TP Gateway:

L2TP Server IP:

Username:

Password:

Reconnect Mode:

Maximum Idle Time:

DNS Servers:

Internet Setup

L2TP

Choose L2TP (Layer 2 Tunneling Protocol) if your ISP uses a L2TP connection. Your ISP will provide you with a username

and password. This option is typically used for DSL services.