1. Home
    2. /
  2. Manuals
    3. /
  3. D-Link
    4. /
  4. DCS-920
    5. /
  5. 13
Page 61 / 72 Scroll up to view Page 56 - 60
µ1
D-Link DCS-910/9±0 User Manual
Appendix A - Wireless Basics
Security
Don’t let you next-door neighbors or intruders connect to your wireless network. Secure your wireless network by turning
on the WPA or WEP security feature on the router. Refer to product manual for detail information on how to set it up.
There are basically two modes of networking:
•
Infrastructure
– All wireless* clients will connect to an access point or wireless router.
•
Ad-Hoc
– Directly connecting to another computer, for peer-to-peer communication, using wireless network
adapters on each computer, such as two or more DCS-920 wireless network Cardbus adapters.
An Infrastructure network contains an Access Point or wireless router. All the wireless devices, or clients, will connect
to the wireless router or access point.
An Ad-Hoc network contains only clients, such as laptops with wireless cardbus adapters. All the adapters must be in
Ad-Hoc mode to communicate.
* Applicable only for the DCS-920
Wireless Modes
Page 62 / 72
µ±
D-Link DCS-910/9±0 User Manual
Appendix B - Networking Basics
Networking Basics
Check your IP address
After you install your new D-Link adapter, by default, the TCP/IP settings should be set to obtain an IP address from a
DHCP server (i.e. wireless router) automatically. To verify your IP address, please follow the steps below.
Click on
Start
>
Run
. In the run box type
cmd
and click
OK
.
At the prompt, type
ipconfig
and press
Enter
.
This will display the IP address, subnet mask, and
the default gateway of your adapter.
If the address is 0.0.0.0, check your adapter
installation, security settings, and the settings
on your router. Some firewall software programs
may block a DHCP request on newly installed
adapters.
If you are connecting to a wireless network at a
hotspot (e.g. hotel, coffee shop, airport), please contact an employee or administrator to verify their wireless network
settings.
Page 63 / 72
µ²
D-Link DCS-910/9±0 User Manual
Appendix B - Networking Basics
Statically Assign an IP address
If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps
below:
Step 1
Windows
®
Vista - Click on
Start
>
Control Panel
>
Network and Internet
>
Network and Sharing Center
>
Manage
Network Connections
.
Windows XP - Click on
Start
>
Control Panel
>
Network Connections
.
Step 2
Right-click on the
Local Area Connection
which represents your D-Link network adapter and select
Properties
.
Step 3
Highlight
Internet Protocol (TCP/IP)
and click
Properties
.
Step 4
Click
Use the following IP address
and enter an IP address that is on the same
subnet as your network or the LAN IP address on your router.
Example: If the router´s LAN IP address is 192.168.0.1, make your IP address
192.168.0.X where X is a number between 2 and 99. Make sure that the number
you choose is not in use on the network. Set Default Gateway the same as the LAN
IP address of your router (192.168.0.1).
Set Primary DNS the same as the LAN IP address of your router (192.168.0.1). The
Secondary DNS is not needed or you may enter a DNS server from your ISP.
Step 5
Click OK twice to save your settings.
Page 64 / 72
µ³
D-Link DCS-910/9±0 User Manual
Appendix C - Technical Specifications
Technical Specifications
Network*
•
TCP/IP (DHCP or Static IP Address)
•
Wired LAN: 10/100Mbps
• 802.11g Wireless (Supports up to 54Mbps transfer rate)**
•
802.11b Wireless (Supports up to 11Mbps transfer rate)**
Web Access Requirements
• Any Java-Enabled or ActiveX compatible Web Browser,. i.e.
current versions of Microsoft Internet Explorer or Netscape
Navigator
™
.
Media Streaming Protocol
• HTTP
Video Specification
• Resolution: 640 x 480
• Sensor: 1/4” color CMOS sensor
• Gain Control: 30 dB
• Exposure: Automatic
• White Balance: Automatic
• Shutter Electronics: 1/30 ~ 1/30,000 sec
• Minimum Illumination: 1 [email protected]
• Focal Length: 5.01mm lens
• Aperture: F2.8
Image (Video Setting)
• Motion-JPEG compression
• Frame rate: 30fps@160 x 120, 30fps@320 x 240,
15fps@640 x 480
• Compression Rate Selection: 5 level (Very Low, Low, Medium,
High, Very High)
• Video Resolution: 160x120, 320x240, 640x480
Web Configuration Requirements
• Internet Explorer 6.0 or above or Netscape 6.0 or above
•
266MHz processor
•
32MB memory (64MB recommended)
• VGA Card Resolution: 800 x 600 or above
Dimensions
• 2.8” (Width) x 4.3” (Depth) x 1.5” (Height)
PC System Requirements
•
Connection to 802.11b/g wireless or Ethernet network
•
Windows
®
Vista or XP
•
1.3GHz processor
•
128MB memory
•
20GB available hard disk space
• CD-ROM drive
Power Source:
• 5V, 2.5A
* Maximum wireless signal rate derived from IEEE Standard 802.11a
and 802.11g specifications. Actual data throughput will vary. Network
conditions and environmental factors, including volume of network
traffic, building materials and construction, and network overhead,
lower actual data throughput rate.
** Applicable only for the DCS-920
*** Environmental conditions may adversely affect wireless signal
range.
Page 65 / 72
µ´
D-Link DCS-910/9±0 User Manual
Appendix C - Technical Specifications
Power Consumption:
• DCS-910 (3.25W), DCS-920 (4.25W)
Environmental specification
•
Operating temperature: 0
°
C to 40
°C (32°
F to 104
°F)
•
Storage temperature: -20
°
C to 70
°
C (-4
°
F to 158
°F)
•
Operating relative humidity: 20% to 80% non-condensing
Warranty:
• 1 Year

Rate

4.5 / 5 based on 2 votes.

Popular D-Link Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top